RIDGID KJ-2200 Quick Start Manual

Engine
Maintain the engine as directed in the engine operator's
manual supplied with the unit.
Pump Lubrication
Check the pump oil level prior to use. Place the jetter on
a level surface. Wipe any dirt and debris from the area
of the dipstick and remove the dipstick – check the oil
level. If needed, add SAE 30W non-detergent oil. Do not
overfill. Reinstall dipstick.
Change oil in pump after first 50 hours of operation
and every 500 hours of operation after that. With the
pump warm from operation, remove plug on bottom of
pump and drain oil into suitable container. Replace
plug. Fill with approximately 32 oz of SAE 30W non-de-
tergent oil using the checking procedure.
Gearbox Lubrication
Check the gearbox oil level prior to use. Place the jetter
on a level surface. Wipe any dirt and debris from the
area of the dipstick and remove the dipstick – check the
oil level. If needed, add SAE 90W gear lubricant. Do not
overfill. Reinstall dipstick.
Change oil in gearbox every 500 hours of operation.
With the gearbox warm from operation, remove plug on
bottom of gearbox and drain oil into suitable container.
Replace plug. Fill with approximately 8 oz of SAE 90W
gear lubricant oil using the checking procedure.
Preparing Pump for Cold Weather
Storage
If the jetter will be stored under conditions
NOTICE
where the temperature is near or below 32°F (0°C),
the jetter must be properly prepared. If water freezes in
the pump, it can damage it.
There are two methods for preparing the jetter for cold
weather storage. The first is to open all valves in the sys-
tem and use compressed air to force any water out of
the system. This can also be used to remove water
from the hoses.
The second method uses RV antifreeze (non-ethylene
glycol antifreeze). Do not use ethylene glycol antifreeze
in the jetter pump. Ethylene glycol cannot be used in
drainage systems.
1. Attach a 3 foot section of hose to the inlet supply
valve and open valve.
2. Place the end of the hose into the container of RV an-
tifreeze.
3. Remove the nozzle from the end of the hose.
KJ-2200/KJ-3100 Water Jetting Machines
4. Start the jetter and run until antifreeze comes out of
the end of the hose.
Accessories
To reduce the risk of serious injury, only use ac-
cessories specifically designed and recommended
for use with the RIDGID Water Jetter Machines,
such as those listed below. Other accessories suit-
able for use with other tools may be hazardous
when used with RIDGID Water Jetter Machines.
KJ-2200 Jetter Nozzles and Hoses
Catalog Model
No. No. Description
64772 H-61 Propulsion Nozzle
64777 H-62 Penetrating Nozzle
64782 H-64 Drop Head Nozzle
82842 H-65 Spin Nozzle 2200
64787 H-71 Propulsion Nozzle
64792 H-72 Penetrating Nozzle
82852 H-75 Spin Nozzle 2200
47592 H-1425 1 / " x 25'
4
47597 H-1435 1 / " x 35'
4
47602 H-1450 1 / " x 50'
4
49272 H-1475 1 / " x 75'
4
49277 H-1400 1 / " x 100'
4
64732 H-1415 1 / " x 150'
4
50002 HL-1 Flexible Leader,
50007 HL-2 Flexible Leader,
47607 H-1250 1 / " x 50'
2
47612 H-1275 1 / " x 75'
2
47617 H-1200 1 / " x 100'
2
51587 H-1211 1 / " x 110'
2
49487 H-1215 1 / " x 150'
2
51597 H-1220 1 / " x 200'
2
KJ-2200 Jetter Accessories
Catalog Model
No. No. Description
62882 H-5 Mini Hose Reel (No Hose included)
64737 H-30 H-30 Cart with Hose Reel
62877 H-30 WH H-30 Cart with Hose Reel and 110' x
64077 HP-22 Pressure Wash Package, KJ-2200
64767 HW-22 Wash Wand, KJ-2200
51572 H-1235 Wash Wand Hose
48157 FV-1 Foot Valve
66732 HF-4 Quick Connect Hose
48367 H-25 Winterizing Kit
47542 H-21 Nozzle Cleaning Tool
67187 H-32 Jet Vac
WARNING
Hose Hose
I.D.
1 / " NPT
8
Fits 1 / " Hose
4
1 / " NPT
4
Fits 1 / " Hose
2
3 / "
16
3 / "
16
1 / " Trap Hose 3 / "
4 16
Orange 3 / "
16
3 / "
16
3 / "
16
"
1 / 1 / "
4 8
"
1 / 1 / "
2 8
1 / "
4
1 / "
4
1 / "
4
1 / " Jet Hose 1 / "
2 4
Black 1 / "
4
1 / "
4
1 / " Jet Hose
2
1 / " x 35'
2
O.D.
1 / "
4
1 / "
4
1 / "
4
1 / "
4
1 / "
4
1 / "
4
3 / "
16
3 / "
16
1 / "
2
1 / "
2
1 / "
2
1 / "
2
1 / "
2
1 / "
2
15