Honeywell 7800 Series Manual page 30

RM7800E,G,L,M
OPERATION
TABLE 4—SELECTABLE MESSAGES (Continued)
Selectable Message
(Second Line)
◊*fault —message*<
◊sequence—message<
◊(second-line-msg)<
◊Fault Cycle
◊Fault Hours
◊Fault Code
◊*fault —message*<
◊sequence—message<
◊(second-line-msg)<
◊Fault Cycle
◊Fault Hours
◊Fault Code
◊*fault —message*<
◊sequence—message<
◊(second-line-msg)<
◊Fault Cycle
◊Fault Hours
◊Fault Code
◊*fault —message*<
◊sequence—message<
◊(second-line-msg)<
◊Diagnostic Info↔
◊Device
◊Device Suffix
◊Run/Test Sw.
◊Operating Control (OperControl)
◊Interlock
◊Pilot Valve
◊Main Valve
◊Ignition
◊LowFire Sw
◊HighFireSw
◊Preignition Interlock (PreIgn ILK)
◊Pilot Valve/First Stage OilValve (Valv/Start,V25) T21 ON or OFF <
◊Jumper 1
◊Jumper 2
◊Jumper 3
◊Amplifier Type (Amp Type)
◊Flame Response
◊Purge Time
◊Manufacturing Code (Mfg Code)
◊Software Revision (SW Rev.)
◊Expanded Annun.↔ (see Table 5)
◊Remote Command
EXPANDED ANNUNCIATOR MESSAGES,
See Table 5
The Expanded Annunciator (EA) may or may not be
connected because it is an optional device. If the EA is not
connected, a display message of "(EA not connected)" will
be shown. If the EA is connected, display messages will be
Display Value
(Second Line)
nnnnn <
nnnnn <
nnn <
nnnnn <
nnnnn <
nnn <
nnnnn <
nnnnn <
nnn <
RM78nnx <
nnnn <
RUN or TEST <
T6 ON or OFF <
T7 ON or OFF <
T8 ON or OFF <
T9 ON or OFF <
T10 ON or OFF <
T18 ON or OFF <
T19 ON or OFF <
T20 ON or OFF <
INTACT or CLIPPED <
INTACT or CLIPPED <
INTACT or CLIPPED <
NORMAL or AMP-CHECK
or SHUTTER
0.8s or 3s <
mm:ss <
nnnn <
nnnn/nnnn <
NONE/HOLD/HF/LF
shown, see Table 5 and 7800 SERIES System Annunciation
Diagnostics and Troubleshooting, form 65-0118, Tables 6
and 7 for fault codes. When accessing Expanded Annuncia-
tor Messages, follow the same operations as used with the
Selectable Messages.
30
First Line
Message
↓H3
↓H3
↓H3
↓H4
↓H4
↓H4
↓H4
↓H4
↓H4
↓H5
↓H5
↓H5
↓H5
↓H5
↓H5
↓H6
↓H6
↓H6
↓H6
↓H6
↓H6
↓DI
↓DI
↓DI
↓DI
↓DI
↓DI
↓DI
↓DI
↓DI
↓DI
↓DI
↓DI
↓DI
↓DI
↓DI
↓DI
↓DI
↓DI
↓DI
↓DI