G0813 Inventory - Grizzly G0813 Owner's Manual

G0813 Inventory

The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
NOTICE
If you cannot find an item on this list, care-
fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack-
ing or they are pre-installed at the factory.
A
C
G
F
I
J
Figure 9. Component inventory.
M N
Q
T
U
Figure 10. Additional component inventory.
Model G0813/G0814/G0814X (Mfd. Since 10/19)
B
D
E
H
K
L
P
O
S
R
V
X
W
Component Inventory (Figures 9–10)
A. Jointer Assembly w/Carriage Mount ........... 1
B. Motor .......................................................... 1
C. Fence Assembly & Carriage ..................... 1
D. Cutterhead Guard ....................................... 1
E. Belt Guard .................................................. 1
F. Knife-Setting Jig ......................................... 1
G. Push Blocks ................................................ 2
H. Hex Wrench 3mm .................................1 Ea.
I.
Belt ............................................................. 1
J.
Fence Lock w/Locking Nut ......................... 1
K. Fence Tilt Handle ....................................... 1
L. Open-End Wrenches 8/10, 12/14mm ...1 Ea.
M. Front Panel w/Switch .................................. 1
N. Right Panel ................................................. 1
O. Left Panel ................................................... 1
P.
Rear Panel (w/Switch Box, Cords) ............. 1
Q. Corner Supports ......................................... 4
R. Top Plate .................................................... 1
S. Dust Port .................................................... 1
T.
Foot Pedal Caster Assembly ...................... 1
U. Motor Mount Plate ...................................... 1
V.
Left Chute Support ..................................... 1
W. Right Chute Panel ...................................... 1
X. Mobile Base Chassis .................................. 1
Fasteners (Not Shown)
• Flange Screws #10-24 x
• Hex Nuts #10-24 (Stand) ............................ 4
• Carriage Bolts ⁄ "-18 x
5
16
• Flat Washers ⁄ " (Motor/Stand) ................. 4
5
16
• Hex Nuts ⁄ "-18 (Motor/Stand) .................. 4
5
16
• Hex Bolts ⁄ "-16 x 1" (Mb. Base/Stand) ..... 4
3
8
• Flat Washers ⁄ " (Mobile Base/Stand) ....... 8
3
8
• Hex Nuts ⁄ "-16 (Mobile Base/Stand) ........ 4
3
8
• Hex Bolts ⁄ "-16 x 2
3
8
• Flat Washers ⁄ " (Wheel/Stand) ................ 4
3
8
• Hex Nuts ⁄ "-16 (Wheel/Stand) .................. 2
3
8
• Hex Bolt ⁄ "-18 x 2" (Wheel/Stand) ........... 1
5
16
• Flat Washer ⁄ " (Wheel/Stand) ................. 1
5
16
• Hex Bolts ⁄ "-16 x
3
8
• Flat Washers ⁄ " (Jointer/Stand) ................ 3
3
8
• Hex Bolt ⁄ "-18 x 2
5
16
• Flat Washer ⁄ " (Belt Guard) ..................... 1
5
16
• Flange Screws #10-24 x
Qty
⁄ " (Stand) ........ 54
3
8
⁄ " (Motor/Stand) .. 4
5
8
⁄ " (Wheel/Stand) ....... 2
1
2
⁄ " (Jointer/Stand) ......... 3
3
4
⁄ " (Belt Guard) ........... 1
1
2
⁄ " (Dust Port) ..... 4
3
8
-19-