Advertisement
Data and Installation
S-Quad Semi-flush
fixing kit (S4-FLUSH)
An S-Quad device can be semi-flush mounted to a ceiling tile to a
depth of the approximate 20mm, which is slightly deeper than the
base assembly. To semi-flush mount a special housing must be
used, which consists of a main assembly and a trim ring.
"
There is an enhanced volume output of sound
and speech from a flush mounted S-Quad.
Clamp
Cut a 140mm
diameter hole in the
ceiling tile.
(
If required use a Bi-Metal Holesaw
140mm or 146mm, from
)
www.shop4tools.co.uk
Insert the flush shroud
assembly into the hole
in the ceiling tile.
Hold the flush shroud
to the ceiling tile and tighten
the three screws to splay the
clamps to secure the shroud to the tile.
Fit the metal box onto the back
of the flush shroud using the
appropriate fixing screws to secure
the box to the flush shroud.
Locate the S-Quad Base into
the flush shroud, such that the
two locating pillars on the
shroud feeds through the two
elongated holes on the Base.
Push the Base into the shroud
until the Base click locks into
the shroud.
Make the cable connections.
Offer the trim ring to the shroud
and slowly rotate ring clockwise until it
clicks and goes no further. This will
lock the ring in position.
Offer the S-Quad to the Base
and rotate the S-Quad clockwise
until it moves upwards into Base,
and then rotate the S-Quad again
until it clicks and goes no further.
WEEE Directive:
At the end of their useful life, the packaging,
product and batteries should be
disposed of via a suitable recycling centre.
Do not dispose of with your normal household waste.
Do not burn.
At the end of their useful life, the packaging,
product and batteries should be disposed of
via a suitable recycling centre and in
accordance with national or local legislation.
Gent by Honeywell reserves the right to revise this publication from time to time and make changes to the content hereof without
obligation to notify any person of such revisions of changes.
Hamilton Industrial Park, Waterside Road, Leicester LE5 1TN, UK
Telephone +44 (0) 116 246 2000
4
www.acornfiresecurity.com
Technical data
Metal back box
S-Quad Base
S-Quad
Do not over tighten the clamping
screws as this will cause the
clamps to cut into the ceiling tile.
Further information about
these products can be found
in Part 2 of this document
available on Gent Expert
website.
www.acornfiresecurity.com
Weight
164g with trim ring
Dimensions
174mm diameter by 50mm depth
Enclosure
ABS
Colour
RAL 9010
Storage Temperature -20°C to 70°C
Ambient temperature -10°C to 50°C
Relative Humidity
95% non condensing
(5 to 45°C)
Cross section
of Ceiling Tile
Flush shroud
Trim ring
Product
No.
S4-710
S4-711
S4-711-ST
S4-711-VO
S4-711-ST-VO 0832-CPD-0510
S4-715
S4-720
S4-720-ST-VO 0832-CPD-0609
S4-771
S4-770
S4-780
S4-911
S4-911-ST-VO 0832-CPD-0512
4188-779 issue 8-7_08/10_S-Quad _Part 1
S-Quad
0832
Gent by Honeywell
Hamilton Industrial Park,
140 Waterside Road,
Leicester LE5 1TN, UK
EC Certification
of Conformity No.
0832-CPD-0706
0832-CPD-0513
0832-CPD-0514
0832-CPD-0608
0832-CPD-0707
0832-CPD-0516
0832-CPD-0511
0832-CPD-0708
0832-CPD-0517
0832-CPD-0515
Website: www.gent.co.uk
Fax (UK): +44 (0)116 246 2300
Advertisement
