How To Conduct A Lamp Test; How To Disable The Local Buzzer - Honeywell GENT COMPACT-MAINS-DAU Commissioning Instructions

How to conduct a lamp test

All the LEDs on the Mains Powered DAU door and the local buzzer inside the unit can be tested by conducting a lamp test.
Mains Powered DAU
L1
VIGILON L
PB1
ON by Honeywell
ON XX/XX/XX
1 2 3 4 5 6 7 8
OFF
SW1
RESET
Press and hold the
Reset button for 5 seconds
to activate a Lamp test.

How to disable the local buzzer

The local buzzer provides audible indications of Mains Powered DAU system fault events. During commissioning it may be
necessary to temporarily disable the local buzzer by configuring a switch on the HMI Board. The switch is located on the inside of the
door.
Set switch position 8 to:
ON - Buzzer enabled
OFF - Buzzer disabled
ON
ON
1 2 3 4 5 6 7 8
OFF
&
Always re-enable the buzzer at the end of the commissioning process before leaving site for normal
operation of the Mains Powered DAU.
www.acornfiresecurity.com
N PE L
01 L2 02 I/A I/B O/A O/B I/A I/B O/A O/B IN+ IN- E 0V A 0V T 0V 0UT 0V OUT 0V S1+ S1- S2+ S2-
NO COM N/O COM N/C
P2
N LOOP AUDIO LOOP PA LOOP LOCAL EVAC ALERT TEST AUX FAULT LINE LINE SPEAKER SPEAKER FS3 3.15A(T)
RELAY RELAY OUT1 OUT2 1 2 Mains fuse
PB3 PB5 AUDIO PB12 PB13 PB14 PB10 PB11
PB4 PB15 PB2 PB6 PB7
N L
VIG CONFIG
DISABLE
P12 ENABLE
1A0 (F)
FS1
1A0 (F)
FS2
P1
AMP 1
P22 P2
P1
P3
AMP 2
P21
P2
P1
PB9 P11 PB16 CAN CAN ACS CONFIG ACS CONFIG SW1
P7
DISABLE H DISABLE BATT
EMIC P6
0V
ENABLE L ENABLE
0V Tx Rx RESET POWER
P9 SUPPLY
Indications given on unit door
green
amber
Low tone for 1s
High tone for 1s
Low tone for 1s
Buzzer
Mains Powered DAU
L1 01 L2 02
VIGILON L N LOOP
PB1
VIG CONFIG
DISABLE
P12 ENABLE
P2
ON PB9
ON by Honeywell XX/XX/XX
1 2 3 4 5 6 7 8
OFF
www.acornfiresecurity.com
will illuminate for 3s
red
N PE L
I/A I/B O/A O/B I/A I/B O/A O/B IN+ IN- E 0V A 0V T 0V NO COM N/O COM N/C 0UT 0V OUT 0V S1+ S1- S2+ S2-
P2
AUDIO LOOP PA LOOP LOCAL EVAC ALERT TEST AUX FAULT LINE LINE SPEAKER SPEAKER FS3 3.15A(T)
PB3 PB5 AUDIO PB12 PB13 PB14 PB15 RELAY RELAY PB2 OUT1 PB6 PB7 OUT2 PB10 PB11 1 2 Mains fuse
PB4 N L
1A0 (F)
FS1
1A0 (F)
FS2
P1
AMP 1
P22 P2
P1
AMP 2 P3
P21
PB16 P1
P11 CAN CAN ACS CONFIG ACS CONFIG SW1 P7
EMIC DISABLE 0V H P6 DISABLE BATT
ENABLE L ENABLE
0V Tx Rx P9 RESET POWER SUPPLY
Mains Powered DAU
15