Honeywell MAXPRO NVR XE Quick Install Manual

®
MAXPRO NVR XE Quick Install Guide
(Express Edition)
Entry Level Network Video Recorder
Document 800-16129V1 – Rev B – 02/2014
Introduction
Welcome to your new Honeywell MAXPRO
installing your NVR, please read this guide carefully.
Unpack
Check that the items received match those listed on the order form and packing slip. The packing box should include, in
addition to your NVR unit and this guide:
Recovery DVD
MAXPRO NVR Client Software (Single Site) and Server
Software DVD (includes manuals)
MAXPRO Viewer Multi-Site Viewing Software Kit
(includes DVD and Getting Started Guide). Not shown.
Note Other peripheral hardware (owner supplied) will also be needed for your installation, such as cameras, network PoE
switch for the camera network, network switch for a client workstation network, a monitor, and an optional keyboard
controller.
Install the Hardware
Mount the MAXPRO NVR XE Unit Mount the MAXPRO NVR XE unit on a flat surface, horizontally or vertically, using the
supplied chassis feet.
Connect the Hardware
Rear Panel
4
3
1
2
7-8 9-10
5 6
Connect a local monitor
to one of the monitor
outputs.
# Connector Connects to...
1 VGA Port VGA monitor
2 Display Port DP Monitor
3 LAN1 - Camera Network Port Network
4 LAN2 - Client/Workstation Network Port Network
5 DVI-D Port DVI Monitor
6 HDMI Port HDMI Monitor
7-8 USB 3.0 Ports (x2) Various devices
9-10 USB 2.0 Ports (x2) Various devices
11 SPDIF Out Not used
12-16 Audio IN/OUT Not used
17 AC Power Electrical outlet
Keyboard Controller (Optional) Follow the documentation that was
included with your IP keyboard controller to connect it to the NVR.
®
NVR XE. This guide helps you set up the NVR right out of the box. Before
Chassis feet
Connect up to 16 IP cameras to a
camera network PoE switch and
the switch to the LAN1 camera
network port.
Connect power cord
17
12–16
11
Connect supplied keyboard
and mouse before powering
up the NVR.
Network Connections Connect a network PoE switch to the camera network port at the rear of the MAXPRO NVR unit.
Connect your cameras to the network PoE switch with CAT5 Ethernet cables. Optionally, connect the client workstation
1
network port to your client workstation network via a network switch. This allows remote access to your NVR. The default
client workstation network IP address must be changed to an available static IP address on your client workstation network.
Monitor(s) The MAXPRO NVR XE comes with built-in graphics and four types of monitor outputs. The unit supports
connection of a single monitor using one of the outputs.
HDMI Output
DVI-D Output
VGA Output
Display Port Output
The recommended resolution for your monitor is 1280 x 1024 pixels (minimum 1024 x 768) and display colors of at least 32
bit.
Dual Network Configuration
Local Monitor (not supplied)
USB
VGA/DVI-D/HDMI/DP
USB
Camera Network
Port (default
192.168.1.101)
Camera Network PoE Switch
CAT5e
CAT5e
CAT5e
H4D2F1
HD4HDIH
H3D2F1
HD3HDIH
Honeywell and Third-Party
IP Cameras
Contact your dealer to purchase Honeywell and third-party IP and analog cameras and encoder.
Power Up the Unit
Note Honeywell recommends using an uninterruptible power supply (UPS) for the NVR unit, the camera network switch,
and the cameras to ensure that the NVR can continue to record video during a power outage. If you need to monitor
video during a power outage, consider a UPS for the monitor as well.
1. Before powering up the NVR, turn on camera(s) and other devices — such as a network switch or router — connected
to the NVR.
2. Press the power button on the front of the NVR.
Front Panel
3. After powering up, you are prompted to log on. The Default user is user name: Administrator, password: Password1.
The user name and password are case sensitive.
The setup wizard starts automatically but may take two minutes. Proceed to
to HDMI monitor
to DVI monitor
to VGA monitor
to DP monitor
®
MAXPRO NVR XE
Router/
Firewall
Client Workstation
Network Port
(default 172.25.254.101)
Client Workstation Network Switch
CAT5e
CAT5e CAT5e
HCD2F
HCD5HIH
Analog Cameras
HDD activity
Honeywell IP Camera
Document 800-16129V1 – Rev B –02/2014
Mobile Devices
Network
Wireless
Router
CAT5e
Client Workstation
Open CD/DVD-
ROM drive tray
Power button
Power LED (green)
On = system powered up.
Configuration.