Honeywell MAXPRO NVR SE Quick Install Manual

MAXPRO
(Standard Edition)—Rev B
Network Video Recorder
Quick Install Guide
Document 800-14458V6 – Rev A – 08/2016
Introduction
Welcome to your new Honeywell MAXPRO
out of the box. Before installing your NVR, please read this guide carefully.
Note Translated Quick Install Guides can be accessed on your MAXPRO NVR unit after logging
in, by clicking on Start menu
Unpack
Check that the items received match those listed on the order form and packing slip. The packing
box should include, in addition to your NVR unit and this guide:
Recovery USB Flash Drive
MAXPRO NVR Client Software
(Single Site) and Server Software
DVD (includes manuals)
MAXPRO Viewer Multi-Site Viewing
Software Kit (includes DVD and
Getting Started Guide). Not shown.
Note Other peripheral hardware (owner supplied) will also be needed for your installation
(such as cameras, network PoE switch for the camera network, network switch for a
client workstation network, a monitor, and an optional keyboard controller).
Install the Hardware
Mount the MAXPRO NVR SE Unit
a rack with the supplied rail hardware kit. The kit allows the NVR to slide in and out of the rack it is
mounted in and provides rear support for the chassis. Refer to the installation instructions included
with the rail hardware kit.
To remove the bezel from the front of the unit, turn the bezel key lock clockwise to loosen, then pull
away from the unit.
To secure the front bezel, turn the bezel key lock counterclockwise.
Hard drive release button. The
first drive is the one on the top left.
Connect the Hardware

Rear Panel

1
# Connector
1 AC Power
2 VGA Port
3 DVI-D Port
4 Display Port
5 HDMI Port
6 LAN1 - Camera Network Port
7 USB Ports (x4)
8 LAN2 - Client Network Port
9 S/PDIF (Optical)
10-14 Audio Inputs and Outputs
www.honeywell.com/security
®
NVR SE
®
NVR SE. This guide helps you set up the NVR right
 
Honeywell Quick Install Guides.
Not shown: HDMI to DVI adapter
MAXPRO NVR DDNS Installation Instructions
Rail hardware kit (includes manual)
Mount the MAXPRO NVR SE unit either on a flat surface or in
1 2
MAXPRO ® NVR SE
Connect IP cameras to a
camera network PoE switch and
the switch to the LAN1 camera
network port.
10-14
2 8
6
4
Display Port
DVI
HDMI
3 5 7 9
Connect supplied
keyboard and mouse
before powering up
the NVR.
Connect a local monitor
to one of the monitor
outputs.
Connects to...
Electrical outlet
VGA monitor
DVI monitor
DP monitor
HDMI monitor
Network
Various devices
Network
Not used
Keyboard Controller (Optional)
documentation that was included with your IP keyboard
controller to connect it to the NVR.
Network Connections
NVR. Connect your cameras to the network PoE switch with CAT5 Ethernet cables. Optionally,
connect the client workstation network port to your client workstation network via a network switch.
This allows remote access to your NVR. The default client workstation network IP address must be
changed to an available static IP address on your client workstation network.
Monitor(s)
The unit supports connection of two monitors using any two of the outputs.
The recommended resolution for your monitor is 1280 x 1024 pixels (minimum 1024 x 768) and
display colors of at least 32 bit.
Dual Network Configuration
1 2
MAXPRO ® NVR SE
H4D2F1
HD4HDIH
Honeywell and Third-Party
IP Cameras
Contact your dealer to purchase Honeywell and third-party IP and analog cameras and encoder.
Power Up the Unit
Note
1.
2.

Front Panel LEDs

3.
Note
Follow the
Connect a network PoE switch to the camera network port at the rear of the
The MAXPRO NVR SE comes with built-in graphics and four types of monitor outputs.
HDMI Output to HDMI monitor
DVI-D Output to DVI monitor
VGA Output to VGA monitor
Display Output to DP monitor
Local Monitor (not supplied)
®
MAXPRO NVR SE
USB
VGA/DVI-D/HDMI/DP
USB
Camera Network Port Client Workstation Network
(default 192.168.1.101) Port (default 172.25.254.101)
Camera Network PoE Switch Client Workstation Network Switch
CAT5e CAT5e
CAT5e
CAT5e
CAT5e
CAT5e
HCD2F
HCD5HIH
Encoder
H3D2F1
HD3HDIH
Analog Cameras
Honeywell recommends using an uninterruptible power supply (UPS) for the MAXPRO
NVR SE unit, the camera network switch, and the cameras to ensure that the NVR can
continue to record video during a power outage or during transient power events. If you
need to monitor video during a power outage, consider a UPS for the monitor as well.
Before powering up the NVR, turn on camera(s) and other devices — such as a network
switch or router — connected to the NVR.
Press the power button on the front of the NVR.
System reset
Power button
Power LED (blue)
On = system powered up
After powering on the unit, you are prompted to log on. The Default user is user name:
NVR-Admin, password: Password$123. The user name and password are case sensitive.
You will be prompted to create a new password the first time that you log in.
The setup wizard starts automatically but may take two minutes to initiate.
Translated Quick Install Guides can be accessed on your MAXPRO NVR unit after logging

in, by clicking on Start menu Honeywell
Mobile Devices
Router/
Firewall
Network
Wireless
Router
CAT5e
CAT5e
Client Workstation
Alarm mute
HDD activity
HDD Fan Fail LED (red)
LAN1, LAN2 LEDs
Off = not supported

Quick Install Guides.
800-14458V6 – Rev A – 08/2016