Makita DVC866L Instruction Manual page 11

ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION:
Always wear dust mask during
assembly or maintenance.
Installing the powder filter (HEPA)
and prefilter (for dry dust)
Optional accessory
CAUTION:
Never pick up water or other liq-
uids or wet dusts when using the powder filter.
Picking up such things may cause the powder filter
breakage.
To use powder filter:
1.
Remove the filter cage and cloth filter.
► Fig.10: 1. Filter cage 2. Cloth filter
2. Place the prefilter in the tank while aligning the
mounting position markings.
3. Mount the damper on the powder filter and then
place them in the prefilter while aligning the mounting
position markings.
4.
Mount the tank cover and lock it.
► Fig.11: 1. Tank cover 2. Powder filter (HEPA)
3. Damper 4. Prefilter 5. Tank 6. Mounting
position marking
NOTICE:
Before using the powder filter, make
sure that prefilter and damper are used together. It
is not allowed to install powder filter alone.
Installing the paper pack
Optional accessory
WARNING:
Before using the paper pack,
make sure that the cloth filter or prefilter is used
together. Failure to use the cloth filter / prefilter
together may cause unusual noise and heat, resulting
in a fire.
NOTICE:
Never pick up water or other liquids or
wet dusts when using the paper pack. Picking up
such things may cause the paper pack breakage.
NOTICE:
When using the cloth filter, make sure
that the float and the float cage are attached on
the tank cover.
NOTICE:
When using the prefilter, make sure
that the powder filter and the damper are used
together.
1. Extend the paper pack.
2. Align the paper pack opening with the dust suction
opening of the cleaner.
3. Insert the cardboard part of the paper pack onto the holder
so that it is positioned at the end beyond the detent protrusion.
► Fig.12: 1. Paper pack 2. Holder
Installing the polyethylene bag
Cleaner can also be used without polyethylene bag.
However, using polyethylene bag is easier to empty the
tank without letting your hands dirty.
Spread the polyethylene bag in the tank. Insert it between
the holder plate and the tank, and pull it to the hose inlet.
► Fig.13: 1. Holder plate 2. Polyethylene bag
Spread the bag around the top of the tank so that the cloth
filter / prefilter edge can catch and hold the bag securely.
► Fig.14: 1. Cloth filter / prefilter
NOTE: A polyethylene bag available on the
market can be used. 0.04 mm or thicker one is
recommended.
NOTE: Too much dust will tear the bag easily, so
do not collect the dust more than the half of the bag
capacity.
Emptying the polyethylene bag
WARNING:
cleaner is switched off and the battery cartridge is
removed before emptying the polyethylene bag.
Failure to do so may cause an electric shock and
serious personal injury.
CAUTION:
Do not apply a great impact on the
tank. Applying a great impact may cause deformation
and damage to the parts.
CAUTION:
Empty the tank at least once a day
although this depends on picked-up dust volume
in the tank. Or, the suction force will weaken and the
motor may be broken.
CAUTION:
Do not grab the hook when empty-
ing the tank. Grabbing the hook may cause the hook
to break.
Unhook and lift up the tank cover.
Shake off the dust from the cloth filter / prefilter and then
take the polyethylene bag out of the tank.
► Fig.15
NOTE: Take the polyethylene bag carefully out of the
tank so that the polyethylene bag cannot be caught
and torn by the protrusion inside the tank when emp-
tying it.
NOTE: Empty the polyethylene bag before it
becomes full. Too much dust in the tank may cause
the polyethylene bag to be torn.
Installing the tool box
1.
Release the lock of the battery cover, and open
the battery cover.
2. Set the rails on the tool box along the grooves on
the housing.
3. Close the battery cover and apply the lock.
► Fig.16
The tool box is convenient for carrying batteries, pipe,
or cuffs.
► Fig.17
11 ENGLISH
Always make sure that the