Operation; Maintenance; Optional Accessories - Makita CL183D Instruction Manual

• Be sure to empty out the dust inside the cleaner itself.
Failure to do so may cause the filter to be clogged or
the motor to be damaged.
In order to drop dust sticking on the filter in the capsule,
tap the circumference of the capsule 4 or 5 times with
your hand. (Fig. 4)
Now point suction inlet downwards, turn capsule in
direction of arrow in diagram, and disconnect capsule
slowly and straight. (Fig. 5)
NOTE:
• Dust may spill out when opening capsule. Be sure to
keep capsule as vertical as possible, and place a
garbage bag beneath capsule.
Remove accumulated dust from inside of capsule and off
of prefilter. (Fig. 6)
Twist prefilter in direction of arrow to unfasten securing lip
from cleaner unit and then pull off prefilter. (Fig. 7)
Clean out fine dust from prefilter. Next, remove filter, and
lightly tap to dislodge dust. (Fig. 8)
Reassembly
First, put filter without being peeled back. If filter is put on
incorrectly, dust will get into motor housing, and cause
motor failure. Second, put prefilter over filter. (Fig. 9)
Turn the set of filters, and adjust the position of the two
securing lips on prefilter, and connect with the gutters of
the cleaner housing. (Fig. 10)
Connect capsule, in accordance with alignment marks on
handle and capsule, firmly twist capsule in direction of
arrow until it is secured. (Fig. 11 & 12)
NOTE:
• Always remove dust ahead of time, as suction power
will be reduced if there is too much dust in cleaner.
• Always be sure to check that both filter and prefilter are
loaded correctly prior to using cleaner. If they are not
loaded correctly, dust will get into the motor housing,
and cause motor failure.

OPERATION

CAUTION:
• Insert (or extract) nozzle while twisting it clockwise. If
twisted counterclockwise, capsule may become loose.
(Fig. 13)
Things to Check Before Asking for Repairs
Symptom
Weak suction power
Not working
010051
NOTE:
• Do not attempt to repair cleaner by yourself.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
10
Area to be investigated
• Is capsule full of dust?
• Is filter clogged?
• Is battery exhausted?
• Is battery exhausted?
Cleaning (Suction)
Nozzle (Fig. 14)
Attach the nozzle to clean off tables, desks, furniture, etc.
Nozzle slips on easily.
Nozzle + Extension wand (Straight pipe) (Fig. 15)
The extension wand fits in between the nozzle and the
cleaner itself. This arrangement is convenient for cleaning
a floor while standing erect.
Corner nozzle (Fig. 16)
Fit on the corner nozzle for cleaning corners and crevices
of a car or furniture.
Corner nozzle +Extension wand (Straight pipe)
(Fig. 17)
In tight quarters where the cleaner itself cannot squeeze
in, or in high places hard to reach, use this arrangement.
Cleaning without nozzle (Fig. 18)
You can pick up powder and dust without nozzle.

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off before
attempting to perform inspection or maintenance.
Cleaning (Fig. 19)
From time to time wipe off the outside (cleaner body) of
the cleaner using a cloth dampened in soapy water.
Clean out also the suction opening, dust bag/dust pack
mounting area and the dust stopper.
CAUTION:
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Wash the filter in soapy water when it is clogged with dust
and the cleaner power becomes small. Dry it out
thoroughly before use. An insufficiently dried filter may
cause poor suction and shorten the service life of the
motor. (Fig. 20)
Do not blow dust sticking on the cleaner by air duster. It
brings dust into the housing and causes failure.
• Empty dust from capsule.
• Dust down or wash filter.
• Recharge battery.
• Recharge battery.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
Fixing method