Safety Information; General Safety Information; Information As Per En 60730; Weee Directive - Honeywell CENTRA LINE EAGLEHAWK NX Installation & Commissioning Instructions

EAGLEHAWK NX CONTROLLER – INSTALLATION & COMMISSIONING INSTRUCTIONS

SAFETY INFORMATION

General Safety Information

When performing any work, all instructions given by the
►
manufacturer and in particular the safety instructions
provided in these Installation and Commissioning
Instructions are to be observed. Make sure that the local
standards and regulations are observed at all times.
The EAGLEHAWK NX System (including the
►
EAGLEHAWK NX controller, Panel Bus I/O modules,
manual disconnect modules, and auxiliary terminal
packages) may be installed and mounted only by
authorized and trained personnel.
If the controller housing is damaged or missing,
►
immediately disconnect it from any power.
If the device is broken or defective, do not attempt to repair
►
it yourself; rather, return it to the manufacturer.
It is recommended that devices be kept at room tem-
►
perature for at least 24 hours before applying power. This
is to allow any condensation resulting from low shipping /
storage temperatures to evaporate.
The EAGLEHAWK NX System must be installed in such a
►
manner (e.g., in a lockable cabinet) as to ensure that
uncertified persons have no access to the terminals.
In the case of vertical mounting on DIN rails, the
►
EAGLEHAWK NX controller should be secured in place
using a commercially-available stopper.
If the EAGLEHAWK NX System is modified in any way,
►
except by the manufacturer, all warranties concerning
operation and safety are invalidated.
Rules regarding electrostatic discharge should be followed.
►
Use only accessory equipment which comes from or has
►
been approved by Honeywell.

Information as per EN 60730

Purpose
The purpose of the device is: OPERATING CONTROL. The
EAGLEHAWK NX controller is a multifunctional non-safety
control device intended for HVAC in home (residential,
commercial, and light-industrial) environments.
Construction
The EAGLEHAWK NX controller is an independently mounted
electronic control unit with fixed wiring.
Mounting Method
The EAGLEHAWK NX controller is suitable for mounting as
follows:
in cabinets;
►
in fuse boxes conforming with standard DIN43880, and
►
having a slot height of max. 45 mm;
in cabinet front doors (using accessory MVC-80-AC2);
►
on walls (using accessory MVC-80-AC1).
►
EN1Z-1039GE51 R1218
Table 1. Information as per EN 60730
Shock protection
Pollution degree
Installation
Rated impulse voltage
Automatic action
Software class
Ball-pressure test
temperature

WEEE Directive

WEEE: Waste Electrical and Electronic
Equipment Directive
 At the end of the product life, dispose
of the packaging and product in an
appropriate recycling center.
 Do not dispose of the device with the
usual domestic refuse.
 Do not burn the device.

Standards, Approvals, etc.

Degree of Protection: IP20 (mounted on walls, with two
accessory MVC-80-AC1 covers)
IP30 (mounted in cabinet doors, with
accessory MVC-80-AC2)
Device meets EN 60730-1, EN 60730-2-9, UL60730, and
UL916.
Refer to Code of Practice standards IEC 61000-5-1 and -2
for guidance.
The device complies with Ethernet Protocol versions IEEEC
802.3.
The device supports BACnet IP and BACnet MS/TP
communications as per ANSI / ASHRAE 135-2012.

3RD-PARTY SOFTWARE LICENSES

This product contains software provided by third parties. See
also EAGLEHAWK NX Controller – Third-Party Software
Licenses (Product Literature No.: EN2Z-1041GE51).
2
Class II
2
Class 3
330 V for SELV, 2500 V for relay
outputs
Type 1.C (micro-interruption for
the relay outputs)
Class A
housing parts >75 °C
terminals >125 °C