Sharp MD-X8 Operation Manual page 42

(Continued)
WW T I M E RWWWR E C
WWO NWWWWWW
WWO F F
WW S O U R C E
WW V O L U M E
Performing timer recording
2
3
WWW 0 9 . 2 7 . ' 9 8
WWWWWWWWWWW
WWWWWWWWWWWWWWWWWWWWW
WWWWWWWWWWWWWWWWWWWWW
WWWWWWWWWWWWWWWWWWWWW
To check the timer setting
2
WW T I M E
WWO NWWWWWW
3
WWO F F
WW S O U R C E WWM D
WW V O L U M E
To cancel the timer operation
2
WWW 0 9 . 2 7 . ' 9 8
WWWWWWWWWWW T I M E RWR E C Y
3
WWWWWWWWWWWWWWWWWWWWW
WWWWWWWWWWWWWWWWWWWWW
WWWWWWWWWWWWWWWWWWWWW
38-58
Y WWWWWWW
p mW 2 : 3 0 WWWW
WWWWW p mW 3 : 3 0 WWWW
WW T U N E RW P - 0 1 W
WWW 0 WWWWWWWWW
WWWWWWWW
WWWWWW T I M E R S T A N D B Y
WWWWW WWWWWW T T I M E R S E T WWWW
W S L E E P W S E T WWWW
WWWWWA D J U S T T WW
T I M E W R
WWG O O DWB Y E ! WWWWWW
WWWWWWWWWWWWWWWWW
WWWWWWWWWWWWWWWWW
WWWWWWWWWWWWWWWWW
WWWWWWWWWWWWWWWWW
WW 1 0 : 3 0 p m
T I M E RWR E C Y
WWWWWWWW
WWWWWWC A N C E L T I M E R Y
WWWWWWC A L L WWWWW T T I M E R WWW
W S L E E P W S E T WWWW
WWWWWA D J U S T T I M E T W R WW
RWWW P L A Y WWWWWWW
a mW 6 : 3 0 WWWW
WWWWW a mW 7 : 4 0 WWWW
N E RW P - 0 1 W
WWW 0 WWWWWWWWW
WWWWWWWW
WWWWWWC A N C E L T I M E R Y
WWWWW WWWWWWC A L L T T I M E R WWW
W S L E E P W S E T WWWW
WWWWWA D J U S T T I M E T W R WW
WW 1 0 : 3 5 a m
41
To change a setting:
1
Turn the power on, and perform steps 1 - 2 on page 40. Then,
select the item you want to change, and set its value as
required.
2
After completing the changes, press the ENTER button.
H H H H H Performing timer recording
1
After timer recording settings have been stored, press the
TIMER/DELETE button.
2
Press the or on the MULTI CONTROL button to select
"TIMER STANDBY".
I If a time has not been set, this will not appear on the display. Set the
time.
3
Then, within 10 seconds, press the ENTER button.
I The unit will enter the timer recording stand-by mode. (Power will be
turned off.)
Note:
In the following cases, the timer recording function will not work
I When a MiniDisc has not been inserted
I When a playback-only MiniDisc is inserted
I When the MiniDisc you inserted is protected against accidental
erasure
I When there is no recording space left on the MiniDisc you have
inserted (when the "TOC FULL" or "DISC FULL" message appears)
To check the timer setting:
1
While in the timer standby mode, press the TIMER/DELETE
button.
2
Press the or on the MULTI CONTROL button to select
"TIMER CALL".
3
Within 10 seconds, press the ENTER button.
I The timer settings will appear in order. Then, after 5 seconds, the
original display will reappear.
To cancel the timer operation:
If the power is turned on, the timer will be canceled.
The timer operation can also be canceled as follows.
1
While in the timer standby mode, press the TIMER/DELETE
button.
2
Press the or on the MULTI CONTROL button to select
"TIMER CANCEL".
3
Within 10 seconds, press the ENTER button.
I The timer operation will be canceled. ( "TIMER" or "TIMER PLAY" will
disappear.) The start and stop times will be stored.
41
98.6.23, 10:34 AM