Sharp MD-X8 Operation Manual page 15

(Continued)
TIMER/
DELETE
TUNING/CURSOR
NAME/
TOC EDIT
_
A B C D E F G H I J K L M 1 2 3 + _ / =
1
N O P Q R S T U V W X Y Z 4 5 6 ! ? & % $
a b c d e f g h i j k l m 7 8 9
n o p q r s t u v w x y z * 0 # , . ; : _
L
A B C D E F G H I J K L M 1 2 3 + _ / =
2
N O P Q R S T U V W X Y Z 4 5 6 ! ? & % $
a b c d e f g h i j k l m 7 8 9
n o p q r s t u v w x y z * 0 # , . ; : _
B I S T
A B C D E F G H I J K L M 1 2 3 + _ / =
1
N O P Q R S T U V W X Y Z 4 5 6 ! ? & % $
a b c d e f g h i j k l m 7 8 9
n o p q r s t u v w x y z * 0 # , . ; : _
B E S T
A B C D E F G H I J K L M 1 2 3 + _ / =
2
N O P Q R S T U V W X Y Z 4 5 6 ! ? & % $
a b c d e f g h i j k l m 7 8 9
n o p q r s t u v w x y z * 0 # , . ; : _
*01-16
MULTI CONTROL
ENTER
MESSAGE
, ,,
( ) @
, ,,
( ) @
q H I T S v w
, ,,
( ) @
q H I T S v w
, ,,
( ) @
14
H H H H H Entering standard size characters
P r e p a r a t i o n
Put the unit in the mode in which characters can be
entered.
I To store radio station names in memory, perform steps 1 - 3 on page
21.
I To create a disc name on an MD, perform steps 1 - 3 on page 36.
I To change the messages displayed when the power is turned on or off,
perform steps 1 - 3 on page 49 or on page 51.
1
Press the , , or
make the character you want to enter start flashing.
I Each time the button is pressed, the character which is flashing will be
changed by one in the direction printed on the button. When the button
is held down, the selection will move continuously in that direction.
I To enter a space, make the
2
Press the ENTER button.
I The selected character will appear in the character entry column.
Then, perform steps 1 - 2 repeatedly to enter the other characters you
need.
3
After entering all the characters
For a radio station name, MD disc name, or MD track
name:
Press the NAME/TOC EDIT button.
For the messages displayed when the power is turned
on or off:
Press the MESSAGE button.
I The characters will be stored in memory.
H H H H H To correct, add, or delete a character
1
Press the 3 TUNING/CURSOR 2 button to move to the
position of the character you want to delete, correct, or add. It
will flash when selected.
2
When you want to delete or correct a character:
Press the TIMER/DELETE button.
I The character will be erased.
I If you want to correct a character, then, enter the correct character.
When you want to add a character:
Press the MULTI CONTROL button to select the position
where you want to add a character, select the new charactor
and then press the ENTER button.
3
Finally, perform step 3 above.
14
98.6.23, 10:30 AM
on the MULTI CONTROL button to
symbol flash.