Honeywell IntelliPath Series Installation And Setup Manual page 22

IGSMHS4G Installation and Setup Guide
PROMPTS
Program Device?
3
(Y/N)_
Create Password?
4
(Y/N)_
Change
5
Password?
(Y/N)_
Enter Password
6
Verify Password
7
Exit Prog. Mode?
8
(Y/N)_
Comm Path
9
Choice
(IP&GSM)_
Device Mode
10
(ECP)_
Important Information Regarding Primary and Secondary Accounts (Prompts 11-17)
Account information is provided by the central station administrator. If the control panel supports secondary
account reporting, you will need secondary account information. The City ID, CS ID or Subscriber ID of the
secondary account must differ from that of the primary account.
Primary City ID
11
(??)_
Primary CS ID
12
(??)
Primary Sub ID
13
(????)
En. 2nd CS Y/N
14
(N)_
3-4
OPTIONS
[Y], [N ] To begin programming the communicator, press [Y] and go to Prompt
10: "Device Mode."
To create a password if none has been assigned, press [N] and go to
Prompt 4: "Create Password."
To change an existing password, press [N] and go to Prompt 5:
"Change Password."
[Y], [N] Passwords can be used to protect account and programming
information.
If no password has been assigned, this prompt appears after pressing
[N] at the "Program Device?" prompt.
If a password is desired, press [Y] and go to "Enter Password."
[Y], [N] If a password has already been assigned, this prompt appears after
pressing [N] at the "Program Device?" prompt.
Press [Y] if you want to change the password.
NOTE: To clear an existing password, without entering a new one,
answer [Y] to the "Change Password?" prompt, then press the [Enter]
key when prompted for the new password and its confirmation.
[0-9, A-F, N, S, This prompt is displayed if [Y] was pressed in Prompt 4 or 5.
T, X, Y] Enter a 4-digit password (0-9, A-F, N, S, T, X, Y).
[0-9, A-F, N, S, Re-enter the password as confirmation.
T, X, Y] If the password doesn't match the first entry, the following is
displayed followed by the "Exit Prog. Mode?" prompt:
Verify Not OK
PSWD not created
Otherwise, the "Exit Prog. Mode?" prompt is displayed directly.
[Y], [N] Exits program mode.
Press [N] to go back to Prompt 3.
[ESC]
Press [ESC] to load factory defaults.
Refer to the Exiting Programming Mode paragraph in this section.
• IP&GSM Press the [space] key to scroll through the communication path
choices. Press [ENTER] to select.
• IP
For maximum reliability, select IP&GSM, and ensure the Internet is
• GSM
connected using the Ethernet cable.
NOTE: After going from a "GSM" only com path choice to an "IP"
only choice, Prompt 41: "DHCP" will default to No.
• ECP Press the [space] key to scroll through the modes of operation. Press
[ENTER] to select ECP mode.
• Zone Triggers
IMPORTANT, if either Zone Trig, 4204 Emu, or Two 4204s device
• 4204 Emu
mode is desired, use Table 3-4 for programming.
• Two 4204s
[01-99]
Enter the 2-digit primary city ID, 01-99 (decimal).
[01-FE] Enter the 2-digit primary central station ID number, 01-FE (HEX).
Enter the 4-digit subscriber account number, 0001-9999 (decimal).
[0001-9999]
Applicable only if control panel supports Central Station #1 and #2
[Y], [N]
Category Enable reporting for the communicator device (e.g., VISTA-
128BP, FA1660C).
DESCRIPTION