Honeywell SiX Series Installation Instructions Manual page 5

HUSH FEATURE / ALARM SILENCE
If required, the audible alarm for CO conditions can be
silenced for 5 minutes by pushing the "Test/Hush"
button. In addition, low chirping can be silenced for 12
hours when the Test/Hush button is pressed.
During a CO alarm, if carbon monoxide is still present
after the 5-minute hush period, the alarm will sound.
CO SENSOR END-of-LIFE FEATURE
When the CO sensor has passed end-of-life, a trouble
signal is sent to the controller (if programmed). This
indicates that the CO sensor inside the detector must be
replaced. If unresolved for 30 days, the detector will chirp
every 45 seconds. The typical life of the CO sensor is ten
years from the date of manufacture. It is recommended
to periodically check the "Replace by" date located on
the label on the back of the detector head.
Carbon Monoxide Detector: Events and Their ID Codes
Event
CO Alarm / CO Alarm
CO Test / CO Test
Low Battery / Low Battery
Detector Supervision /
Detector Supervision
Detector End-of-Life/Trouble
Detector End-of-Life/Trouble
Tamper / Tamper
TESTING SIGNAL STRENGTH
Perform this test in accordance with NFPA 72
inspection, testing and maintenance requirements to
determine a strong communication path with the control
panel.
1. Activate the wireless system's GO/NO GO TEST mode.
2. Press the detector's TEST button (•) for 1-2 seconds.
The detector should immediately transmit an alarm
signal to the control panel. The built-in horn will start
to sound about 2.5 seconds after pressing the button.
3. The wireless system's keypad should emit at least
three beeps when the alarm transmission is received
and display the transmitting detector's zone number.
4. When the console has received the test signal, the
horn will stop and a few seconds later the detector's
zone number will clear from the console display.
5. If the console does not respond as noted, and if this is
an initial installation, try moving the detector to
another location that provides proper reception. Also,
be sure that the detector has been "enrolled" by the
controller (see Enrollment section). Then, repeat the
test.
6. Turn off the system's TEST mode (typically security
code + OFF).
Alpha Keypad
CO Alarm
CO Alarm
Lo Bat
CO Trouble
/
CO Trouble
Disarmed .......... CO Trouble
Armed ................. CO Alarm
HUSH FEATURE / ALARM SILENCE
If required, the audible alarm for CO conditions can be
silenced for 5 minutes by pushing the "Test/Hush"
button. In addition, low chirping can be silenced for 12
hours when the Test/Hush button is pressed.
During a CO alarm, if carbon monoxide is still present
after the 5-minute hush period, the alarm will sound.
CO SENSOR END-of-LIFE FEATURE
When the CO sensor has passed end-of-life, a trouble
signal is sent to the controller (if programmed). This
indicates that the CO sensor inside the detector must be
replaced. If unresolved for 30 days, the detector will chirp
every 45 seconds. The typical life of the CO sensor is ten
years from the date of manufacture. It is recommended to
periodically check the "Replace by" date located on the
label on the back of the detector head.
CS Report
CO Alarm (CID 162)
CO alarm (CID 162)
RF low-battery (CID 384)
RF sensor supervision (CID 381)
supervision (CID 381)
Sensor Trouble - End-of Life (CID 380)
- End-of Life (CID 380)
RF Sensor Tamper (CID 383)
TESTING SIGNAL STRENGTH
Perform this test in accordance with NFPA 72 inspection,
testing and maintenance requirements to determine a
strong communication path with the control panel.
1. Activate the wireless system's GO/NO GO TEST mode.
2. Press the detector's TEST button (•) for 1-2 seconds.
The detector should immediately transmit an alarm
signal to the control panel. The built-in horn will start
to sound about 2.5 seconds after pressing the button.
3. The wireless system's keypad should emit at least three
beeps when the alarm transmission is received and
display the transmitting detector's zone number.
4. When the console has received the test signal, the horn
will stop and a few seconds later the detector's zone
number will clear from the console display.
5. If the console does not respond as noted, and if this is
an initial installation, try moving the detector to
another location that provides proper reception. Also,
be sure that the detector has been "enrolled" by the
controller (see Enrollment section). Then, repeat the
test.
6. Turn off the system's TEST mode (typically security
code + OFF).
5
/ CO Alarm (CID 162)
/ CO Alarm (CID 162)
/ RF Low-Battery (CID 384)
/ RF sensor
/ Sensor Trouble
/ RF Sensor Tamper