Makita DGA408 Instruction Manual
Cordless angle grinder
Hide thumbs
Also See for DGA408:
- Instruction manual (164 pages) ,
- Instruction manual (49 pages) ,
- Instruction manual (112 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita DGA408
Summary of Contents for Makita DGA408
- Page 1 INSTRUCTION MANUAL Cordless Angle Grinder DGA408 DGA458 DGA508 Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: DGA408 DGA458 DGA508 Wheel diameter Max. wheel thickness 6.4mm Spindle thread 8,500min Overall length 348mm BL1815N, BL1820, BL1820B 362mm BL1830B, BL1840, BL1840B, BL1850, BL1850B, BL1860B Net weight 2.2kg 2.4kg BL1815N, BL1820, BL1820B 2.5kg 2.6kg BL1830B, BL1840, BL1840B, BL1850, BL1850B, BL1860B Rated voltage D.C.18 V... -
Page 3: Ec Declaration Of Conformity
Keep children and bystanders away while NOTE: operating a power tool. Distractions can cause been measured in accordance with the standard test Electrical Safety another. Power tool plugs must match the outlet. Never NOTE: modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. - Page 4 Power tool use and care Cordless grinder safety warnings Do not force the power tool. Use the correct power tool for your application. Safety Warnings Common for Grinding, Sanding, Wire Brushing, or Abrasive Cutting-Off Operations: rate for which it was designed. This power tool is intended to function as a Do not use the power tool if the switch does grinder, sander, wire brush or cut-off tool.
- Page 5 Cutting-Off Operations: area of operation. Use only wheel types that are recommended 10. Hold the power tool by insulated gripping surfaces only, when performing an operation designed for the selected wheel. Wheels for where the cutting tool may contact hidden which the power tool was not designed cannot be wiring.
- Page 6 15. If working place is extremely hot and humid, Use extra caution when making a “pocket cut” into existing walls or other blind areas. or badly polluted by conductive dust, use a short-circuit breaker (30 mA) to assure opera- tor safety. 16.
-
Page 7: Functional Description
Follow your local regulations relating to dis- posal of battery. SAVE THESE INSTRUCTIONS. CAUTION: Only use genuine Makita batteries. 1. Red indicator 2. Button 3. charger. while sliding the button on the front of the cartridge. Tips for maintaining maximum... - Page 8 Indicator lamps Remaining Battery indicator status Remaining capacity battery capacity Blinking Lighted Blinking Charge the Tool / battery protection system Charge the is placed under one of the following conditions. In some conditions, the indicators light up. Overload protection malfunctioned. When the tool is operated in a manner that causes it to NOTE: Depending on the conditions of use and the tool off and stop the application that caused the tool to...
- Page 9 Shaft lock Automatic speed change function installing or removing accessories. 1. Mode indicator 1. Shaft lock Mode indicator status Operation mode High speed mode NOTICE: Never actuate the shaft lock when the spindle is moving. Switch action CAUTION: Before installing the battery car- tridge into the tool, always check to see that the depending on the work load.
- Page 10 ASSEMBLY CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. Installing side grip (handle) CAUTION: Always be sure that the side grip is installed securely before operation. 1.
- Page 11 Installing or removing depressed Optional accessory Optional accessory WARNING: Always use supplied guard when Wheel can shatter during use WARNING: When using a depressed center on the tool so that the closed side of the guard always points toward the operator. CAUTION: Make sure that the mounting part result in the dangerous vibration.
-
Page 12: Operation
Grinding and sanding operation model 1. Sanding lock nut 2. 3. Rubber pad workpiece. In general, keep the edge of the wheel or disc at an Mount the rubber pad onto the spindle. angle of about 15° to the workpiece surface. Fit the disc on the rubber pad and screw the sand- During the break-in period with a new wheel, do not ing lock nut onto the spindle. - Page 13 model When installing the abrasive cut-off wheel: 1. Lock nut 2. wheel 3. 4. Wheel guard for abrasive cut-off wheel / diamond wheel 1. Lock nut 2. depressed center wheel. The direction for mounting the lock nut and the When installing the diamond wheel: When installing the abrasive cut-off wheel: 16 m m ( 5/ 8″...
-
Page 14: Maintenance
NOTICE: Avoid applying too much pressure which causes over bending of wires when using wire wheel brush. breakage. MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. -
Page 15: Optional Accessories
OPTIONAL ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool spec- Depressed center wheel / Flap disc Lock nut Back up pad Flex wheel Rubber pad 100 Rubber pad 115 Sanding lock nut Wire wheel brush... - Page 16 Jan-Baptist Vinkstraat 2, M a k i t a E u r o p e N . V . 3070 Kortenberg, Belgium 3- 11-8, Sumiyoshi-cho, M a k i t a C o r p o r a t i o n Anjo, Aichi 446-8502 Japan w w w .