Cisco SCE8000 Configuration Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. SCE8000 GBE
  6. Configuration manual
Cisco SCE8000 Configuration Manual

Cisco SCE8000 Configuration Manual

10gbe platform
Hide thumbs Also See for SCE8000:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Configuration Manual, Installation Manual
Introduction to the Cisco SCE8000 10GBE
Platform
Revised: August 23, 2010, OL-16478-05
Introduction
This chapter provides an introduction to the Cisco SCE8000 10GBE platform, the Service Control
hardware component.
•
•
•
•
•
•
•
•
Information About the SCE Platform
The Service Control Engine (SCE) platform, which is the hardware component of the Cisco Service
Control solution, is designed to support observation, analysis, and control of Internet/IP traffic.
Table 2-1
Table 2-1
Model number
Link Type
Number of Ports
Number of Links
OL-16478-05
The SCE8000-SIP, page 2-8
summarizes model information for the Cisco SCE8000 platform.
SCE Platform Model Information
C H A P T E R
Cisco SCE8000 10GBE
10 Gigabit Ethernet
2 or 4
1 or 2
Cisco SCE8000 10GBE Installation and Configuration Guide
2
2-1

Advertisement

Table of Contents
loading

Related Manuals for Cisco SCE8000

Summary of Contents for Cisco SCE8000

  • Page 1: Table Of Contents

    Introduction to the Cisco SCE8000 10GBE Platform Revised: August 23, 2010, OL-16478-05 Introduction This chapter provides an introduction to the Cisco SCE8000 10GBE platform, the Service Control hardware component. Information About the SCE Platform, page 2-1 • Service Control Module (SCE8000-SCM-E), page 2-3 •...

  • Page 2: Information About The Sce Platform

    One optional optical bypass module hosting panel that holds up to two optical bypass modules. • In addition, the Cisco SCE8000 chassis contains two power supply modules in a 1+1 configuration, as well as a fan tray module. Cisco SCE8000 10GBE Installation and Configuration Guide...

  • Page 3: Service Control Module (Sce8000-Scm-E)

    Introduction to the Cisco SCE8000 10GBE Platform Service Control Module (SCE8000-SCM-E) Service Control Module (SCE8000-SCM-E) The Cisco SCE8000 contains one or two SCE8000-SCMs located in slots#1 and #2 (the top two slots). The Service Control module contains ports and LEDs as shown in Figure 2-2...
  • Page 4 Steady amber — Only one power supply is functioning normally. • Unlit — No power from either power supply. On a slave SCE8000-SMC_E module (in the second slot), this LED is always off. Status The Status LED indicates the operational status of the Cisco SCE8000 system, as follows: Unlit —...

  • Page 5: Introduction To Sips And Spas

    A SIP contains one or more subslots (bays), which are used to house one or more SPAs. The SPA • provides interface ports for network connectivity. During normal operation the SIP should reside in the SCE8000 chassis fully populated either with • functional SPAs in all subslots, or with a blank filler plate (SPA-BLANK=) inserted in all empty subslots.

  • Page 6: Shared Port Adapters

    Introduction to the Cisco SCE8000 10GBE Platform Introduction to SIPs and SPAs Shared Port Adapters The SPA supported by the Cisco SCE8000-SIP is the 1-Port 10-Gigabit Ethernet SPA, SPA-1X10GE-L-V2 The following list describes some of the general characteristics of a SPA: •...

  • Page 7: Xfp Connections

    Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform Introduction to SIPs and SPAs Figure 2-5 10GBE Small Form-factor Pluggable (XFP0) The interface connector on the 1-Port 10-Gigabit Ethernet SPA is a fiber optic receiver that supports one XFP. The types of optics modules that have been qualified for use with the 1-Port 10-Gigabit Ethernet SPA on...

  • Page 8: The Sce8000-Sip

    • The 1-Port 10GBE SPA Interface Module The SCE8000-SIP is installed in slot #3 of the Cisco SCE8000 chassis. It hosts up to four single-width, single-height 1-Port 10GBE SPA interface modules, but in the Cisco SCE8000, it must be configured with either two 1-Port 10GBE SPAs (in the top two subslots) or four 1-Port 10GBE SPAs, to provide interfaces for either one or two complete traffic links.

  • Page 9: The Cisco Sce8000 Optical Bypass

    Optical Bypass Module (OPB-SCE8K), page 2-11 • The Cisco SCE8000 platform optical bypass module preserves the service provider 10GBE links under all circumstances. At power failure the bypass is automatically activated. It can also be activated by the Cisco SCE8000 software.

  • Page 10: Optical Bypass Functionality

    During a power failure —The Cisco SCE8000 has two power supplies. A power failure occurs only when both of them fail. In a case where the Cisco SCE8000 platform must be replaced, it is possible to remove the bypass modules from the SCE8000 chassis without disconnecting them from the network and then reinstall them in the new SCE platform, so that traffic links are preserved even in a case of complete failure and replacement of the Cisco SCE8000 platform.
  • Page 11 OPB-SCE8K-MM supports Multi-Mode optics and should be used with SCE8000 equipped with Multi-Mode optics. The optical bypass module is installed either internally, in slot #4 of the Cisco SCE8000 chassis or in an external mounting panel in the rack. Up to two optical bypass modules can be mounted internally, supporting inline insertion into two links.

  • Page 12: Fan Assembly

    Green — Bypass module has been de-activated (traffic flows through the • Cisco SCE8000 platform) Off — Bypass module is active (traffic does not flow through the Cisco • SCE8000 platform) Optical Bypass Module Specifications Fiber Cable Type The fiber cable type within the Optical Bypass Module area as follows: OPB-SCE8K-MM: 50 um core.
  • Page 13 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform The Cisco SCE8000 Optical Bypass Figure 2-9 Fan Assembly SCE 8000 -SC M-E OPT ICA L FA N BYP ASS CON SOL ST AT U POR T 1 10 100 STA TUS...

  • Page 14: Power Supplies

    Introduction to the Cisco SCE8000 10GBE Platform The Cisco SCE8000 Optical Bypass Power Supplies The Cisco SCE8000 platform supports redundant AC- or DC-input power supplies. The following power supplies are available for the Cisco SCE8000 platform: • 2700 W DC input (PWR-2700-DC/4): uses an external terminal block on the back side of the chassis...

  • Page 15: Checking The Shipping Container Contents

    Do not discard the shipping container when you unpack the Cisco SCE8000. Flatten the shipping cartons and store them with the pallet. You will need these containers if you need to move or ship the Cisco SCE8000 in the future.
  • Page 16 • Control Cable (40 cm) • Cisco does not ship the entire Cisco SCE8000 documentation set automatically with each system. You Note must specifically order the documentation as part of the sales order. If you ordered documentation and did not receive it, we will ship the documents to you within 24 hours. To order documents, contact a customer service representative.

  • Page 17: Cisco Sce8000 Installation Checklist

    Cisco SCE8000 Installation Checklist (Table 2-11). Indicate when each procedure or verification is completed. When the checklist is completed, place it in your site log along with the other records for your new Cisco SCE8000 platform. Table 2-11 Cisco SCE8000 Installation Checklist Task...
  • Page 18 Chapter 2 Introduction to the Cisco SCE8000 10GBE Platform Cisco SCE8000 Installation Checklist Cisco SCE8000 10GBE Installation and Configuration Guide 2-18 OL-16478-05...

Table of Contents