1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Security Camera
  5. 26 series
  6. Quick start manual

HIKVISION 26 series Quick Start Manual

Network bullet camera
Hide thumbs Also See for 26 series:
Table of Contents

Advertisement

Quick Links

Camera
Network Bullet Camera
Quick Start Guide
UD00683B
0

Advertisement

Table of Contents
loading

Related Manuals for HIKVISION 26 series

Summary of Contents for HIKVISION 26 series

  • Page 1 Camera Network Bullet Camera Quick Start Guide UD00683B...
  • Page 2 Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission of Hikvision.
  • Page 3 LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.

  • Page 4: Regulatory Information

    Network Bullet Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
  • Page 5 Network Bullet Camera·Quick Start Guide This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.

  • Page 6: Safety Instruction

    Network Bullet Camera·Quick Start Guide Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
  • Page 7 Network Bullet Camera·Quick Start Guide ● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 24 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information. ●...
  • Page 8 Network Bullet Camera·Quick Start Guide ● The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam. ● Do not place the camera in extremely hot, cold (the operating temperature shall be-30°C ~+60°C, or -40°C ~ +60°C if the camera model has an “H”...
  • Page 9 Network Bullet Camera·Quick Start Guide Table of Contents 1 Appearance Description ............... 10 1.1 Type I Camera ............... 10 1.2 Type II Camera .............. 12 1.3 Type III Camera ............. 14 2 Installation ..................17 2.1 Memory Card Installation ..........18 2.2 Type I Camera Mounting ..........
  • Page 10 Network Bullet Camera·Quick Start Guide 5.1 Hik-Connect Setup ............43 5.2 Adding Device to Hik-Connect ........43 5.3 Initializing the Memory Card ......... 44 0504001060218...

  • Page 11: Appearance Description

    Network Bullet Camera·Quick Start Guide 1 Appearance Description 1.1 Type I Camera The overview of Type I camera is shown below. Figure 1-1 Overview of Type I Camera Table 1-1 Description Description Sun Shield Front Cover...
  • Page 12 Network Bullet Camera·Quick Start Guide Description Zoom and Focus Lever IR LED Lens Air Vent Video Output Interface Reset Button Memory Card Slot Audio Cable Alarm Cable Power Cable Network Cable Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.

  • Page 13: Type Ii Camera

    Network Bullet Camera·Quick Start Guide 1.2 Type II Camera The overview of Type II camera is shown below. Figure 1-2 Overview of Type II Camera...
  • Page 14 Network Bullet Camera·Quick Start Guide Table 1-2 Description Description Sun Shield Front Cover Zoom and Focus Lever IR LED Lens Air Vent Video Output Interface Bracket Reset Button Memory Card Slot Audio Cable Alarm Cable Power Cable Network Cable Grounding...

  • Page 15: Type Iii Camera

    Network Bullet Camera·Quick Start Guide Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. Type III Camera The overview of Type III camera is shown below. Figure 1-3 Overview of Type III Camera (1)
  • Page 16 Network Bullet Camera·Quick Start Guide Figure 1-4 Overview of Type III Camera (2) Table 1-3 Description Description Sun Shield Front Cover IR LED Lens Air Vent Bracket Reset Button Memory Card Slot Video Cable...
  • Page 17 Network Bullet Camera·Quick Start Guide Description Network Cable Power Cable Alarm Cable Audio Cable Grounding Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.

  • Page 18: Installation

    Network Bullet Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or PoE (802.3af), please make sure your power supply matches with your camera.

  • Page 19: Memory Card Installation

    Network Bullet Camera·Quick Start Guide 2.1 Memory Card Installation This series of cameras support memory card installation. Different camera types share the similar installation steps, and we take Type I camera as an example. Steps: 1. Rotate the lock screw counterclockwise to loosen it. Slide the sun shield according to the arrow direction as shown in below.
  • Page 20 Network Bullet Camera·Quick Start Guide Figure 2-2 Remove the Sun Shield 3. Remove the front cover by rotating it counterclockwise. 4. Insert the memory card into the memory card slot. Figure 2-3 Insert the Memory Card 5. Rotate the front cover clockwise back to the camera and install the sun shield back.

  • Page 21: Wall Mounting

    Network Bullet Camera·Quick Start Guide Rotating Label Figure 2-4 Tighten the Front Cover For water-proof performance, align the rotating label on the front cover with that on the camera when you rotate the front cover clockwise. 2.2 Type I Camera Mounting 2.2.1 Wall Mounting Before you start: Wall mounting bracket is not included in the package.
  • Page 22 Network Bullet Camera·Quick Start Guide Pedestal Figure 2-5 Install the Wall Mounting Bracket Insert the expansion screws first if the camera is mounted to a cement wall. And you can use the self-tapping screws directly if the camera is mounted to a wooden wall. 2.

  • Page 23: Pendant Mounting

    Network Bullet Camera·Quick Start Guide 1). Loosen the pan adjusting screw to adjust the panning position [0° to 360°]. Tighten the screw. 2). Loosen the tilt adjusting screw to adjust the tilting position [0° to 90°]. Tighten the screw. 0° to 90° Pan Adjusting Screw 0°...
  • Page 24 Network Bullet Camera·Quick Start Guide Ceiling Pendant Bracket Adjusting Knob Notch Figure 2-8 Fix the Pendant Bracket 2. Loosen and remove the Lock Screw on the sun shield of the camera. 3. Screw the camera to the pendant bracket through the Lock Screw hole.
  • Page 25 Network Bullet Camera·Quick Start Guide 4. Adjust the view angle as shown in Figure 2-10. 1). Loosen the adjusting knob. 2). Rotate the notch to face or be back to your surveillance scene according to your actual need. To obtain larger angel adjustment range, place the notch back to the surveillance scene if your camera monitors downwards, and place the notch facing the surveillance scene if your camera monitors upwards.

  • Page 26: Type Ii And Type Iii Camera Mounting

    Network Bullet Camera·Quick Start Guide 5. Adjust zoom and focus (refer to Section 2.4). 6. (Optional) Install the water-proof jacket for network interface. Refer to Section 2.5 for detailed installation procedures. 2.3 Type II and Type III Camera Mounting Before you start: Camera of these types is equipped with a bracket.
  • Page 27 Network Bullet Camera·Quick Start Guide 3. If you need to route cables through the wall (or the ceiling), cut a cable hole according to the drill template. Skip this step, if you want to route the cables on the surface of the wall (or the ceiling). 4.
  • Page 28 Network Bullet Camera·Quick Start Guide Tilt Adjustment Steps: Loosen the lock screw 2. Adjust the tilting position of the camera. The adjusting range is from 0° to 100°. Tighten the lock screw 2. Rotation Adjustment Steps: Loosen the lock screw 3. Rotate the rotation position to adjust the azimuth angle of the image.

  • Page 29: Mounting With A Junction Box

    Network Bullet Camera·Quick Start Guide 2.3.2 Mounting with a Junction Box Before you start: The junction box is not included in the package. You need to prepare one for this mounting type. Steps: Junction Box Safety Rope Figure 2-14 Mounting with a Junction Box 1.

  • Page 30: Mounting With A Gang Box

    Network Bullet Camera·Quick Start Guide 6. (Optional) Install the water-proof jacket for the network interface. Refer to Section 2.5. 7. Route the cables of the camera. 8. Connect the interfaces to the power on the camera to see if you can get an image on your monitoring screen.

  • Page 31: Zoom And Focus Adjustment

    Network Bullet Camera·Quick Start Guide 4. Connect the interfaces to the power on the camera to see if you can get an image on you monitoring screen. If you can’t get the image, check the connection of the interfaces before performing the next step. 5.
  • Page 32 Network Bullet Camera·Quick Start Guide Steps: 1. Remove the sun shield and front cover to expose the zoom lever and the focus lever. 2. View the camera image on the monitoring screen. 3. Loosen the zoom lever and move the lever between T (Tele) and W (Wide) to obtain the desired angle of view.

  • Page 33: Type Iii

    Network Bullet Camera·Quick Start Guide 2.4.2 Type III Type III camera is equipped with a motor-driven lens. You can adjust the zoom and focus level on PTZ control panel by visiting the camera via web browser or client software. For detailed steps, refer to the User Manual of Network Camera. Figure 2-17 Zoom and Focus Adjustment via Web Browser 2.5 Installation of Network Cable Water-proof...
  • Page 34 Network Bullet Camera·Quick Start Guide Table 2-1 Components Components Camera’s Network Interface Socket O-Type Gasket Network Plug Waterproof Endcap Waterproof Rubber Gasket Lock Nut Network Cable from Router/Switch Steps: Feed the plugless network cable ⑦ through the lock nut ⑥, waterproof rubber gasket ⑤...
  • Page 35 Network Bullet Camera·Quick Start Guide Insert the waterproof rubber gasket ⑤ into the waterproof endcap ④, and secure lock nut ⑥ with the waterproof endcap ④. Align the snap on the waterproof endcap ④ with the notch on the camera’s network interface socket ①, and then secure the waterproof endcap ④...

  • Page 36: Setting The Network Camera Over The Lan

    Network Bullet Camera·Quick Start Guide 3 Setting the Network Camera over the Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection.

  • Page 37: Activating The Camera

    Network Bullet Camera·Quick Start Guide Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take Activation via SADP software and Activation via Web Browser as examples to introduce the camera activation.

  • Page 38: Activation Via Sadp Software

    Network Bullet Camera·Quick Start Guide 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you to create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
  • Page 39 Network Bullet Camera·Quick Start Guide Figure 3-4 SADP Interface Note: The SADP software supports activating the camera in batch. Please refer to the user manual of SADP software for details. 3. Create a password and input the password in the password field, and confirm the password.

  • Page 40: Modifying The Ip Address

    Network Bullet Camera·Quick Start Guide 4. Click OK to save the password. You can check whether the activation is completed on the popup window. If the activation failed, please make sure that the password meets the requirement and try again. Modifying the IP Address Purpose: To view and configure the camera via LAN (Local Area Network), you...
  • Page 41 Network Bullet Camera·Quick Start Guide Figure 3-5 Modify the IP Address 4. Input the password to activate your IP address modification. The batch IP address modification is supported by the SADP; please refer to the User Manual of SADP for details.

  • Page 42: Accessing Via Web Browser

    Network Bullet Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and versions above CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and versions above, Apple Safari 5.0.2 and versions above, Mozilla Firefox 5.0 and versions above and Google Chrome 18 and versions above Steps:...
  • Page 43 Network Bullet Camera·Quick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the plug-in installation.

  • Page 44: Operating Via Hik-Connect App

    Network Bullet Camera·Quick Start Guide 5 Operating via Hik-Connect App Hik-Connect Setup Steps: 1. Download and install the Hik-Connect app by searching “Hik-Connect” in App Store or Google Play 2. Launch the app and register for a Hik-Connect user account. 3.

  • Page 45: Initializing The Memory Card

    Network Bullet Camera·Quick Start Guide find the QR code on the mounting base of the device or on the cover of the Quick Start Guide of the device in the device package. Figure 5-2 Scan QR Code 3. Follow the prompts to set the Wi-Fi connection and add the device to your Hik-Connect account.

Table of Contents