Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-2CD4012F-A
Summary of Contents for HIKVISION DS-2CD4012F-A
- Page 1 Camera Network Box Camera Quick Operation Guide UD.6L0201B1320A01...
- Page 2 Network Box Camera·Quick Operation Guide Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. About This Document This manual applies to the following camera models. Model DS-2CD4012F-(A)(P)(W)(SDI)(FC) DS-2CD4012FWD-(A)(P)(W)(SDI)(FC) DS-2CD4024F-(A)(P)(W)(SDI)(FC) DS-2CD4026FWD-(A)(P)(W) DS-2CD4032FWD-(A)(P)(W)(SDI)(FC)
-
Page 3: Regulatory Information
Network Box Camera·Quick Operation Guide Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. - Page 4 Network Box Camera·Quick Operation Guide 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points.
-
Page 5: Safety Instruction
Network Box Camera·Quick Operation Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected. - Page 6 Network Box Camera·Quick Operation Guide ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed.
- Page 7 Network Box Camera·Quick Operation Guide ● Do not place the camera in extremely hot, cold (the operating temperature shall be-30℃~+60℃,or -40°C ~ 60°C if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation. ●...
-
Page 8: Table Of Contents
Network Box Camera·Quick Operation Guide Table of Contents 1 Appearance Description ..............8 2 Installation ..................12 2.1 Ceiling Mounting ............13 2.2 Wall Mounting .............. 16 2.3 Installing the SD Card ............ 19 3 Setting the Network Camera over the LAN ........20 4 Accessing via Web Browser ............ -
Page 9: Appearance Description
Network Box Camera·Quick Operation Guide Appearance Description The overview of the box camera is shown below: Figure 1-1 Overview (1) The overview of the components and the interface are shown below: Figure 1-2 Overview (2) - Page 10 Network Box Camera·Quick Operation Guide The interfaces on the rear panel are shown below: Figure 1-3 Overview (3) Table 1-1 Description Description Description Lens Mount ¼ -20 UNC Screw Hole Power Indicator...
- Page 11 Network Box Camera·Quick Operation Guide Description Description Auto-iris Interface LAN(PoE) Power Outlet Reset Micro SD Card Slot Video Out Grounding Alarm Out RS-232 RS-485 Alarm In Audio Out Audio In Only the models with “A” in its suffix support ABF function. ...
- Page 12 Network Box Camera·Quick Operation Guide Table 1-2 Pins DC-driven Damp- Damp+ Drive+ Drive- Power, Video and GND pins are used when the auto-iris is driven by video; Damp+, Damp-, Drive+ and Drive- pins are used when the auto-iris is driven by DC.
-
Page 13: Installation
Network Box Camera·Quick Operation Guide Installation Before you start: Make sure the device in the package is in good condition and all the assembly parts are included. Make sure all the related equipment is power-off during the installation. ... -
Page 14: Ceiling Mounting
Network Box Camera·Quick Operation Guide ● Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into the lens causing reflection. ● The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS. - Page 15 Network Box Camera·Quick Operation Guide 2. Fit the lens (not supplied) to the camera and rotate it to get it tightened. Install the adapter ring to the lens interface if a C-mount lens is used. A manual-iris lens can be directly installed to the camera without plugging the power cable of the auto-iris to the auto-iris interface.
- Page 16 Network Box Camera·Quick Operation Guide 5. Adjust the surveillance angle. 1). Loosen the pan nut to adjust the pan angle [0°-360°]. 2). Loosen the knob on the ceiling mount to adjust the tilt angle [0°-90]. 6. Adjust the Lens 1). Connect the VIDEO OUT interface of the camera to the debugging monitor.
-
Page 17: Wall Mounting
Network Box Camera·Quick Operation Guide Wall Mounting Steps: 1. Install the lens (not supplied) to the camera and rotate it to get it tightened. 2. Plug the auto-iris cable to the auto-iris interface. Figure 2-4 Install the Lens 3. Loosen the lock screw on the mount and remove the tilt adjust table from the wall mount. - Page 18 Network Box Camera·Quick Operation Guide Tilt Adjust Table Lock Screw Figure 2-5 Remove the Tilt Adjust Table 4. Fit the removed tilt adjust table to the camera, and fix it with two screws. Figure 2-6 Install the Tilt Adjust Table 5.
- Page 19 Network Box Camera·Quick Operation Guide Figure 2-7 Install the Wall Mount 6. Install the camera to the wall mount and tighten the two lock screws. 7. Adjust the surveillance angle. 1). Loosen the pan nut to adjust the pan angle [0 °-360°]. 2).
-
Page 20: Installing The Sd Card
Network Box Camera·Quick Operation Guide Tilt Adjust Screw Pan Adjust Screw Figure 2-8 Adjust the Surveillance Angle Installing the SD Card Insert the SD card to the SD card slot to get it installed. Push the inserted SD card slightly to get it sprung by its built-in springing to remove it. -
Page 21: Setting The Network Camera Over The Lan
Network Box Camera·Quick Operation Guide Setting the Network Camera over the Purpose: To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the SADP or PCNVR software to search and change the IP of network camera. - Page 22 Network Box Camera·Quick Operation Guide Use PCNVR software and to list the online devices. Please refer to the user manual of PCNVR client software for detailed information. 2. Change the IP address and subnet mask to the same subnet as of your PC.
- Page 23 Network Box Camera·Quick Operation Guide Figure 3-2 Search Online Devices Device can be searched and displayed in the list in 15 seconds after it goes online; it will be removed from the list in 45 seconds after it goes offline. Search online devices manually: You can also click to refresh the online device...
-
Page 24: Modify Device Information
Network Box Camera·Quick Operation Guide You can click on each column heading to order the information; you can click to show the device table and hide the network parameter panel on the right side, or click to show the network parameter panel. ... - Page 25 Network Box Camera·Quick Operation Guide Figure 3-4 Modify Network Parameters 3. Enter the IP address of network camera in the address field of the web browser to view the live video. The default value of the IP address is “192.0.0.64”. The default user name is “admin”, and password is “12345”.
-
Page 26: Accessing Via Web Browser
Network Box Camera·Quick Operation Guide Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 6.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 3.5 and above version and... - Page 27 Network Box Camera·Quick Operation Guide Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in.
- Page 28 Network Box Camera·Quick Operation Guide Figure 4-2 Download Plug-in Figure 4-3 Install Plug-in (1)
- Page 29 Network Box Camera·Quick Operation Guide Figure 4-4 Install Plug-in (2) 6. Reopen the web browser after the installation of the plug-in and repeat steps 2-4 to login. For detailed instructions of further configuration, please refer to the user manual of network camera.