HIKVISION DS-2CD2432F-IW Quick Start Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Security Camera
  5. DS-2CD2432F-IW
  6. Quick start manual

HIKVISION DS-2CD2432F-IW Quick Start Manual

Network cube camera
Hide thumbs Also See for DS-2CD2432F-IW:
Table of Contents

Advertisement

Quick Links

See also: Installation Manual
Network Cube Camera
Quick Start Guide
UD04383N-A
0

Advertisement

Table of Contents
loading

Related Manuals for HIKVISION DS-2CD2432F-IW

Summary of Contents for HIKVISION DS-2CD2432F-IW

  • Page 1 Network Cube Camera Quick Start Guide UD04383N-A...

  • Page 2: Regulatory Information

    Network Cube Camera·Quick Start Guide About this Manual This Manual is applicable to 24xx Network Camera. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
  • Page 3 Network Cube Camera·Quick Start Guide Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
  • Page 4 Network Cube Camera·Quick Start Guide 2. This device must accept any interference received, including interference that may cause undesired operation. EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU, RE Directive 2014/53/EU.
  • Page 5 Network Cube Camera·Quick Start Guide This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence.

  • Page 6: Safety Instruction

    Network Cube Camera·Quick Start Guide This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.
  • Page 7 Network Cube Camera·Quick Start Guide ● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 24 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information. ●...
  • Page 8 Network Cube Camera·Quick Start Guide malfunction), and affect the endurance of sensor at the same time. ● The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam.
  • Page 9 Network Cube Camera·Quick Start Guide responsibility for problems caused by unauthorized repair or maintenance.)
  • Page 10 Network Cube Camera·Quick Start Guide Table of Contents 1 Appearance Description ............... 10 2 Notice ................... 14 3 Installation ..................16 Memory Card Installation ..........17 Stand Mounting ............17 Ceiling Mounting ............19 4 Setting the Network Camera over the LAN ........22 Wiring ................

  • Page 11: Appearance Description

    Network Cube Camera·Quick Start Guide 1 Appearance Description There are two types of appearances for 24 series camera. Please refer to the figure below. And one appearance will be taken as an example in the chapter below. Figure 1-1 Type I Appearance Figure 1-2 Type II Appearance...
  • Page 12 Network Cube Camera·Quick Start Guide Figure 1-3 Overview...
  • Page 13 Network Cube Camera·Quick Start Guide Table 1-1 Description Description Lens Microphone IR LED Alarm: Solid red when the camera is armed; Solid blue when the camera is unarmed Status: Solid blue when the camera is Indicator added to the Guarding Vision Link: Flashing amber when network is connected;...
  • Page 14 Network Cube Camera·Quick Start Guide Description O: Alarm Output Interface Power supply interface (12 VDC) Speaker Note:  Press RESET about 10s when the camera is power on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. ...

  • Page 15: Notice

    Network Cube Camera·Quick Start Guide 2 Notice  Do not install the camera  Do not touch the lens with in the extreme whether your finger. condition.  Do not install the camera  Do not subject the camera towards the strong light or to vibration, shock or in the unstable lightening heavy pressure.
  • Page 16 Network Cube Camera·Quick Start Guide  High humidity may  Under no circumstances damage the camera should you submerge the hardware; put it in dry and camera in any type of well-ventilated place. liquid.  Electromagnetic radiation may affect the video data transmission and the image quality.

  • Page 17: Installation

    Network Cube Camera·Quick Start Guide 3 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with your camera.

  • Page 18: Memory Card Installation

    Network Cube Camera·Quick Start Guide Memory Card Installation This series of camera supports memory card installation. Follow the steps below to install the memory card. Insert the memory card into the card slot on the side of the camera. (Optional) Push the inserted memory card to get it sprung out. Memory Card Figure 3-1 Install Memory Card...
  • Page 19 Network Cube Camera·Quick Start Guide Figure 3-2 Bracket Align the camera body to the bracket, and rotate the camera body to fix it with the bracket. Figure 3-3 Install the Camera Body Assemble the camera as the steps above, and put the camera on the flat surface.

  • Page 20: Ceiling Mounting

    Network Cube Camera·Quick Start Guide Ceiling Mounting Drill the screw holes according to the drill template. Drill Template Screw hole All:for Mounting Base Figure 3-4 Drill Template Disassemble the 3-axis bracket. Hold the base with one hand, and rotate the pole anticlockwise to disassemble the pole from the base.
  • Page 21 Network Cube Camera·Quick Start Guide Knob Pole Base Fixed Tray Figure 3-5 Disassemble the Bracket Install the fixed tray to the ceiling with the supplied screws. Install the base to the fixed plate. Figure 3-6 Install the Fixed Plate and Mounting Base Install the camera to the bracket.
  • Page 22 Network Cube Camera·Quick Start Guide Figure 3-7 Install the Camera Adjust surveillance angel 1). Loosen the knob to adjust the panning position and tilting position. 2). After adjusting the angle of the camera to the desired position, fasten the knob. Knob 360°...

  • Page 23: Setting The Network Camera Over The Lan

    Network Cube Camera·Quick Start Guide 4 Setting the Network Camera over the Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection.

  • Page 24: Activating The Camera

    Network Cube Camera·Quick Start Guide Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation.

  • Page 25: Activation Via Sadp Software

    Network Cube Camera·Quick Start Guide Figure 4-3 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
  • Page 26 Network Cube Camera·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera, please refer to the User Manual of Network Camera for other two activation methods.

  • Page 27: Modifying The Ip Address

    Network Cube Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
  • Page 28 Network Cube Camera·Quick Start Guide Steps: 1. Run the SADP software. 2. Select an activate device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. Figure 4-5 Modify the IP Address...
  • Page 29 Network Cube Camera·Quick Start Guide Note: You can enable the Guarding Vision service for the device during activation. Refer to Chapter 6.1 for detailed information. 4. Input the admin password and click Modify to activate your IP address modification. The batch IP address modification is supported by the SADP. Please refer to the User Manual of SADP for details.

  • Page 30: Accessing Via Web Browser

    Network Cube Camera·Quick Start Guide 5 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps:...
  • Page 31 Network Cube Camera·Quick Start Guide 4. Click Login. Figure 5-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.

  • Page 32: Operating Via Guarding Vision App

    Network Cube Camera·Quick Start Guide 6 Operating via Guarding Vision App Purpose: Guarding Vision is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: Guarding Vision service is not supported by certain camera models. Enable Guarding Vision Service on Camera Purpose: Guarding Vision service should be enabled on your camera before...
  • Page 33 Network Cube Camera·Quick Start Guide “Privacy Policy” Service” Figure 6-1 Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Guarding Vision app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. 6.1.2 Enable Guarding Vision Service via Web Browser Before you start:...
  • Page 34 Network Cube Camera·Quick Start Guide Steps: 1. Access the camera through web browser. Refer to Chapter 5. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access Guarding Vision dev.guardingvision.com Figure 6-2 Platform Access Configuration (Web) 3.

  • Page 35: Guarding Vision Setup

    Network Cube Camera·Quick Start Guide Guarding Vision Setup Steps: 1. Download and install the Guarding Vision app by searching “Guarding Vision” in App Store or Google Play 2. Launch the app and register for a Guarding Vision user account. 3. Log in Guarding Vision app after registration. Adding Camera to Guarding Vision Before you start: You need to enable the Guarding Vision service on camera before...
  • Page 36 Network Cube Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 6-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number.

  • Page 37: Initializing The Memory Card

    Network Cube Camera·Quick Start Guide Initializing the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.

This manual is also suitable for:

24 series

Table of Contents