Makita LS1016 Instruction Manual page 19

Fig.52
There are crown and cove molding joints which
are made to fit "Inside" 90° corners ((1) and (2) in
Fig. A) and "Outside" 90° corners ((3) and (4) in
Fig. A).
(1) (2) (3) (4)
1 2
Fig.A
001556
Fig.53
Measuring
Measure the wall length and adjust workpiece on table
to cut wall contact edge to desired length. Always make
sure that cut workpiece length at the back of the
workpiece is the same as wall length. Adjust cut length
for angle of cut. Always use several pieces for test cuts
to check the saw angles.
When cutting crown and cove moldings, set the bevel
angle and miter angle as indicated in the table (A) and
position the moldings on the top surface of the saw
base as indicated in the table (B).
In the case of left bevel cut
Molding
position in
52/38° type
Fig. A
(1)
For inside
corner
(2)
Left 33.9°
(3)
For outside
corner
(4)
006361
Molding
Molding edge against
position in
guide fence
Fig. A
Ceiling contact edge should
(1)
be against guide fence.
For inside
corner
(2)
Wall contact edge should be
against guide fence.
For
(3)
outside
corner
Ceiling contact edge should
(4)
be against guide fence.
006362
Example:
In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
Tilt and secure bevel angle setting to
•
33.9° LEFT.
Adjust and secure miter angle setting to
•
31.6° RIGHT.
1. Inside corner
2. Outside corner
Table (A)
Bevel angle Miter angle
45° type 52/38° type
Right 31.6°
Left 30° Left 31.6°
Right 31.6°
Table (B)
Finished piece
Finished piece
will be on the
Left side of
blade.
Finished piece
will be on the
Right side of
blade.
In the case of right bevel cut
For inside
corner
For outside
corner
006363
For inside
corner
For
outside
corner
006364
45° type
Right 35.3°
Left 35.3°
Right 35.3°
Crown molding stoppers (optional accessories) allow
easier cuts of crown molding without tilting the saw
blade. Install them on the base as shown in the figures.
Fig.54
Fig.55
Fig. B: At right 45° miter angle
Fig. C: At left 45° miter angle
Position crown molding with its WALL CONTACT
EDGE against the guide fence and its CEILING
CONTACT EDGE against the crown molding stoppers
as shown in the figure. Adjust the crown molding
stoppers according to the size of the crown molding.
Tighten the screws to secure the crown molding
stoppers. Refer to the table (C) for the miter angle.
19
Lay crown molding with its broad back
•
(hidden) surface down on the turn base
with its CEILING CONTACT EDGE
against the guide fence on the saw.
The finished piece to be used will
•
always be on the LEFT side of the blade
after the cut has been made.
Table (A)
Bevel angle
Molding
position in
52/38° type 45° type
Fig. A
(1)
(2)
Right 33.9° Right 30°
(3)
(4)
Table (B)
Molding
Molding edge against
position in
guide fence
Fig. A
Wall contact edge should be
(1)
against guide fence.
(2)
Ceiling contact edge should
be against guide fence.
(3)
Wall contact edge should be
(4)
against guide fence.
Example:
In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
Tilt and secure bevel angle setting to
•
33.9° RIGHT.
Adjust and secure miter angle setting to
•
31.6° RIGHT.
Lay crown molding with its broad back
•
(hidden) surface down on the turn base
with its WALL CONTACT EDGE against
the guide fence on the saw.
The finished piece to be used will
•
always be on the RIGHT side of the
blade after the cut has been made.
Miter angle
52/38° type 45° type
Right 31.6° Right 35.3°
Left 31.6° Left 35.3°
Right 31.6° Right 35.3°
Finished piece
Finished piece
will be on the
Right side of
blade.
Finished piece
will be on the
Left side of
blade.