General Power Tool Safety Warnings; Save All Warnings And Instructions For Future Reference; Miter Saw Safety Warnings - Makita LS1016 Instruction Manual

Waste Electric and Electronic Equipment
and its implementation in accordance with
national law, electric equipment that have
reached the end of their life must be
collected separately and returned to an
environmentally compatible recycling facility.
Intended use
The tool is intended for accurate straight and miter
cutting in wood. With appropriate saw blades, aluminum
can also be sawed.
Power supply
The tool should be connected only to a power supply of the same
voltage as indicated on the nameplate, and can only be operated
on single-phase AC supply. They are double-insulated and can,
therefore, also be used from sockets without earth wire.
Noise
The typical A-weighted noise level determined according
to EN61029:
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Wear ear protection
Vibration
The vibration total
determined according to EN61029:
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test method
and may be used for comparing one tool with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the power
•
tool can differ from the declared emission value
depending on the ways in which the tool is used.
Be sure to identify safety measures to protect the operator
•
that are based on an estimation of exposure in the actual
conditions of use (taking account of all parts of the
operating cycle such as the times when the tool is switched
off and when it is running idle in addition to the trigger time).
For European countries only
EC Declaration of Conformity
Makita declares that the following Machine(s):
Designation of Machine:
Slide Compound Miter Saw
Model No./ Type: LS1016, LS1016L, LS1016F,
LS1016FL
) : 92 dB (A)
pA
) : 101 dB (A)
WA
value (tri-axial vector
2
) : 2.5 m/s or less
h
2
Conforms to the following European Directives:
2006/42/EC
They are manufactured in accordance with the following
standard or standardized documents:
EN61029
The technical file in accordance with 2006/42/EC is
ENE006-1
available from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
ENF002-2
000331
ENG905-1
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

General Power Tool Safety Warnings

WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for
future reference.
ENG900-1
sum)

MITER SAW SAFETY WARNINGS

1. Keep hands out of path of saw blade. Avoid
contact with any coasting blade. It can still
cause severe injury.
ENG901-1
2. Check the saw blade carefully for cracks or
deformation before operation.
Replace damaged blades immediately.
3. Replace the kerf board when worn.
4. Use only saw blades specified by the
manufacturer which conform to EN847-1.
5. Do not use saw blades manufactured from
high speed steel.
6. Wear eye protection.
7. Wear hearing protection to reduce the risk of
hearing loss.
8. Wear gloves for handling saw blade (saw
blades shall be carried in a holder wherever
practicable) and rough material.
9. Connect miter saws to a dust collecting device
when sawing.
10. Select saw blades in relation to the material to be cut.
ENH003-15
11. Do not use the saw to cut other than wood,
aluminum or similar materials.
12. Always secure all moving portions before
carrying the tool. When lifting or carrying the
tool, do not use the guard as a carrying handle.
13. Do not operate saw without guards in place.
Check blade guard for proper closing before each
use. Do not operate saw if blade guard does not
10
30. 6. 2014
Yasushi Fukaya
Director
GEA010-1
ENB034-10