Makita LS1016 Instruction Manual
Slide compound miter saw
Hide thumbs
Also See for LS1016:
- Instruction manual (152 pages) ,
- Technical information (37 pages) ,
- Instruction manual (152 pages)
Related Manuals for Makita LS1016
Summary of Contents for Makita LS1016
- Page 1 INSTRUCTION MANUAL Slide Compound Miter Saw LS1016 LS1016L 009482 DOUBLE INSULATION IMPORTANT: Read Before Using.
-
Page 2: Specifications
ENGLISH (Original instructions) SPECIFICATIONS Model LS1016/LS1016L Blade diameter For all countries other than European countries 255 mm - 260 mm For European countries 260 mm Hole diameter For all countries other than European countries 25.4 mm For European countries 30 mm Max. - Page 3 electronic equipment Dress properly. implementation in accordance with Do not wear loose clothing or jewellery, they can national law, electric equipment that be caught in moving parts. Rubber gloves and have reached the end of their life must non-skid footwear recommended when be collected separately and returned to...
-
Page 4: Additional Safety Rules For Tool
conditions that may affect its operation. A guard or 12. Use only flanges specified for this tool. other part that is damaged should be properly 13. Be careful not to damage the arbor, flanges repaired or replaced by an authorized service (especially the installing surface) or bolt. -
Page 5: Functional Description
FUNCTIONAL DESCRIPTION work. To reduce your exposure to these chemicals: work in a well ventilated area and work with approved safety equipment, CAUTION: such as those dust masks that are Always be sure that the tool is switched off and •... - Page 6 If guard becomes discolored through age or UV light stopper pin to lock the handle in the lowered position. exposure, contact a Makita service center for a new Loosen the locking screw counterclockwise which guard. DO NOT DEFEAT OR REMOVE GUARD.
-
Page 7: Adjusting The Miter Angle
Adjusting the miter angle 1. Lock lever 1. Stopper lever 2. Grip 3. Cam 009517 009736 Push the grip so that the cams engages and turn it First, unplug the tool. Lower the stopper lever to position clockwise until it stops. Turn the turn base while pressing the saw blade as shown in the figure. -
Page 8: Switch Action
CAUTION: simply pull the switch trigger without pressing the Before plugging in the tool, always check to see lock-off button. Return tool to a Makita service • that the switch trigger actuates properly and center for proper repairs BEFORE further usage. - Page 9 Electronic function NOTE: Constant speed control When laser line is dim and almost or entirely • Possible to get fine finish, because the rotating invisible because of the direct sunlight in the indoor • speed is kept constantly even under the loaded or outdoor window-by work, relocate the work area condition.
- Page 10 Always be sure that the tool is switched off and • unplugged before installing or removing the blade. Use only the Makita socket wrench provided to • install or remove the blade. Failure to do so may result in overtightening or insufficient tightening of the hex bolt.
-
Page 11: Securing Workpiece
Make sure shaft lock has released spindle before making cut. NOTE: 1. Hex bolt If you connect a Makita vacuum cleaner to this tool, • more efficient and cleaner operations can be performed. -
Page 12: Fence Adjustment
To adjust the fences before bevel-cutting, loosen a lever 1. Support and slide the upper fence outward. Make a dry run with 2. Turn base the saw turned off and check clearance. Adjust the fence to be as close to the blade as practical to provide maximum workpiece support, without interfering with arm up and down movement. -
Page 13: Operation
Horizontal vise (optional accessory) Holders (Optional accessory) 1. Vise plate 1. Holder 2. Vise nut 2. Screw 3. Vise knob 009606 009607 The horizontal vise can be installed in two positions on The holders can be installed on either side as a either the left or right side of the base. -
Page 14: Personal Injury
Press cutting (cutting small workpieces) 009504 009503 Pull the carriage toward you fully. Switch on the Workpieces up to 68 mm high and 160 mm wide tool without the blade making any contact and wait can be cut in the following way. until the blade attains full speed. - Page 15 "Adjusting the bevel angle"). Be sure to retighten 45° wall angle cove molding. See illustrations. the lever firmly to secure the selected bevel angle 1. 52/38 ﾟ type safely. Secure the workpiece with a vise. Make crown molding sure the carriage is pulled all the way back toward 2.
- Page 16 In the case of left bevel cut Table (B) Table (A) Molding Molding edge against Bevel angle Miter angle position in Finished piece Molding guide fence Fig. A position in 52/38° type 45° type 52/38° type 45° type Fig. A Wall contact edge should be Finished piece Right 31.6°...
-
Page 17: Carrying Tool
Position crown molding with its WALL CONTACT Groove cutting EDGE against the guide fence and its CEILING 1. Cut grooves with CONTACT EDGE against the crown molding blade stoppers as shown in the figure. Adjust the crown molding stoppers according to the size of the crown molding. -
Page 18: Maintenance
1. Triangular rule 009506 009509 Make sure that the pointer points to 0° on the miter CAUTION: scale. If the pointer does not point to 0°, loosen the Always secure all moving portions before carrying • screw which secures the pointer and adjust the the tool. -
Page 19: Laser Radiation
Adjust the 45° bevel angle only after 1. 0 ﾟ Angle performing 0° bevel angle adjustment. To adjusting bolt adjust left 45° bevel angle, loosen the lever 2. Lever and tilt the blade to the left fully. Make sure 3. Latch lever that the pointer on the arm holder points to 45°... - Page 20 Check the position of laser line regularly for • 1. Screw to change the movable range of the adjusting accuracy . screw Have the tool repaired by Makita authorized • 2. Adjusting screw service center for any failure on the laser unit. 3. Hex wrench 4.
-
Page 21: Replacing Carbon Brushes
10 minutes. Then check the tool while running and electric brake operation when releasing the switch trigger. If electric brake is not working well, ask your local Makita service center for repair. After use After use, wipe off chips and dust adhering to the •... - Page 24 Makita Corporation 884886F8...