Makita DGA406 Instruction Manual
Cordless angle grinder
Hide thumbs
Also See for DGA406:
- Instruction manual (92 pages) ,
- Instruction manual (39 pages) ,
- Instruction manual (16 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita DGA406
Summary of Contents for Makita DGA406
- Page 1 INSTRUCTION MANUAL Cordless Angle Grinder DGA406 DGA456 DGA506 Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: DGA406 DGA456 DGA506 Wheel diameter 100mm (4″) 115mm (4-1/2″) 125mm (5″) Max. wheel thickness 6.4mm Spindle thread M14 or 5/8″ (country specific) Rated speed (n) 8,500min Overall length With battery cartridge 348mm BL1815N, BL1820, BL1820B With battery cartridge BL1830,... - Page 3 When operating a power tool outdoors, use an power tool’s operation. If damaged, have the power tool repaired before use. Many accidents extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of are caused by poorly maintained power tools.
- Page 4 The rated speed of the accessory must be at 14. Do not operate the power tool near flammable least equal to the maximum speed marked on materials. Sparks could ignite these materials. the power tool. Accessories running faster than 15. Do not use accessories that require liquid their rated speed can break and fly apart.
- Page 5 Wheels must be used only for recommended If the use of a guard is recommended for wire applications. For example: do not grind with the brushing, do not allow any interference of the side of cut-off wheel. Abrasive cut-off wheels are wire wheel or brush with the guard.
-
Page 6: Functional Description
MISUSE or failure to follow the safety causing fires, personal injury and damage. It will rules stated in this instruction manual may cause also void the Makita warranty for the Makita tool and serious personal injury. charger. Tips for maintaining maximum... -
Page 7: Overload Protection
To remove the battery cartridge, slide it from the tool NOTE: Depending on the conditions of use and the while sliding the button on the front of the cartridge. ambient temperature, the indication may differ slightly To install the battery cartridge, align the tongue on the from the actual capacity. -
Page 8: Overheat Protection
Overheat protection Switch action When the tool is overheated, the tool stops automati- cally and the battery indicator shows following state. In CAUTION: Before installing the battery car- this situation, let the tool cool before turning the tool on tridge into the tool, always check to see that the again. - Page 9 Accidental re-start preventive Installing or removing wheel guard function (For depressed center wheel, flap disc, flex wheel, wire wheel brush Even if the battery cartridge is installed on the tool with / abrasive cut-off wheel, diamond the slide switch in the "I (ON)" position, the tool does wheel) not start.
- Page 10 ► 1. Wheel guard 2. Bearing box 3. Screw 4. Lever ► 1. Lock nut 2. Depressed center wheel 3. Inner flange 4. Mounting part Pull the lever in direction of the arrow. Then tighten the wheel guard with fastening the screw. Be sure to tighten To tighten the lock nut, press the shaft lock firmly so the screw securely.
-
Page 11: Operation
Installing or removing abrasive disc OPERATION Optional accessory WARNING: It should never be necessary to NOTE: Use sander accessories specified in this man- force the tool. The weight of the tool applies ade- ual. These must be purchased separately. quate pressure. Forcing and excessive pressure could cause dangerous wheel breakage. - Page 12 For 100 mm (4″) model Operation with abrasive cut-off / diamond wheel When installing the abrasive cut-off wheel: Optional accessory WARNING: When using an abrasive cut-off / diamond wheel, be sure to use only the special wheel guard designed for use with cut-off wheels. (In some European countries, when using a diamond wheel, the ordinary guard can be used.
-
Page 13: Maintenance
When installing the diamond wheel: Operation with wire wheel brush Optional accessory CAUTION: Check operation of wire wheel brush by running tool with no load, insuring that no one is in front of or in line with the wire wheel brush. -
Page 14: Optional Accessories
The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. •... - Page 15 100 mm (4″) model 115 mm (4-1/2″) model 125 mm (5″) model Inner flange Depressed center wheel / Flap disc Lock nut Back up pad Flex wheel Inner flange and rubber pad 76 Rubber pad 100 Rubber pad 115 Abrasive disc Sanding lock nut Wire wheel brush Wire cup brush...
- Page 16 Makita Corporation 885470A2 20151020 www.makita.com...