Specifications; Functional Description - Makita DA3010 Instruction Manual

ENGLISH
1 Lamp
2 Speed control screw
3 Switch lever
4 Higher

SPECIFICATIONS

Model
Capacities
Steel .................................................................. 10 mm
Wood ................................................................. 25 mm
–1
No load speed (min ) .....................................0 — 2,400
Overall length ..................................................... 270 mm
Net weight ............................................................. 1.4 kg
Safety class ...........................................................
• Due to our continuing programme of research and
development, the specifications herein are subject to
change without notice.
• Note: Specifications may differ from country to country.
Intended use
This tool is intended for drilling in wood, metal and plas-
tic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety Hints
For your own safety, please refer to the enclosed safety
instructions.
ADDITIONAL SAFETY RULES FOR TOOL
1. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tools
may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed
metal parts of the tool "live" and shock the ope-
ator.
2. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not leave the tool running. Operate the tool
only when hand-held.
6. Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
SAVE THESE INSTRUCTIONS.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
4
Explanation of general view
5 Lower
6 Reversing switch lever
7 Chuck key
8 Sleeve
Switch action (Fig. 1)
DA3010/DA3010F
CAUTION:
• Before plugging in the tool, always check to see that
DA3011/DA3011F
To start the tool, simply squeeze the switch lever. Tool
speed is increased by increasing pressure on the switch
lever. Release the switch lever to stop.
A speed control screw is provided so that maximum tool
speed can be limited (variable). Turn the speed control
/II
screw clockwise for higher speed, and counterclockwise
for lower speed.
Reversing switch action (Fig. 2)
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
This tool has a reversing switch to change the direction of
rotation. Move the reversing switch lever to the
tion (A side) for clockwise rotation or the
side) for counterclockwise rotation.
Lighting up the lamps (Fig. 1)
For DA3010F, DA3011F only
CAUTION:
• Do not look in the light or see the source of light
To turn on the lamp, start the tool. Then, the lamp lights
up the top of the bit. To turn it off, stop the tool.
ENB001-1
NOTE:
• Use a dry cloth to wipe the dirt off the lens of lamp. Be
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
Installing side grip (handle) (Fig. 3)
CAUTION:
• Always be sure that the side grip is installed securely
Screw the side grip on the tool securely. The side grip
can be installed on either side of the tool, whichever is
convenient.
9 Ring
10 Gripping part
11 Side grip (handle)
the switch lever actuates properly and returns to the
"OFF" position when released.
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
directly.
careful not to scratch the lens of lamp, or it may lower
the illumination.
unplugged before carrying out any work on the tool.
before operation.
F posi-
position (B
R