Specifications - Makita BHP460 Instruction Manual

ENGLISH
1 Button
2 Battery cartridge
3 Grip base
4 Teeth
5 Side grip
6 Loosen
7 Tighten
8 Depth rod
9 Thumb screw
10 Sleeve

SPECIFICATIONS

Model
Capacities
Concrete ............................................................ 16 mm
Steel .................................................................. 13 mm
Wood ................................................................. 38 mm
Wood screw ........................................ 10 mm x 90 mm
Machine screw ..................................................... 6 mm
-1
No load speed (min )
High ............................................................... 0 – 1,500
Low ................................................................... 0 – 460
Blows per minute
High ............................................................. 0 – 22,500
Low ................................................................ 0 – 6,900
Overall length ..................................................... 267 mm
Net weight (with battery cartridge) ......................... 2.7 kg
Rated voltage ...................................................D.C. 24 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
4
Explanation of general view
11 Bit
12 Bit holder
13 Switch trigger
14 Reversing switch lever
15 A side
16 B side
17 Clockwise
18 Counterclockwise
19 Low speed
20 High speed
BHP460
6.
7.
8.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
2.
3.
4.
ADDITIONAL SAFETY RULES
FOR CHARGER & BATTERY CARTRIDGE
1.
ENC005-1
2.
3.
4.
5.
21 Speed change lever
22 Action mode changing ring
23 Arrow
24 Adjusting ring
25 Graduations
26 Limit mark
27 Brush holder cap
28 Screwdriver
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
Be careful not to drop or strike battery.
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
Do not charge battery cartridge when tempera-
ture is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
Do not attempt to use a step-up transformer, an
engine generator or DC power receptacle.
Do not allow anything to cover or clog the
charger vents.
Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).