Wimius K5 - Video Projector Manual

Safety Precautions

1. Clean
   When clean this projector, please pull out the power cable. Use a wet cloth to clean, don't use any detergent that may damage the unit.
2. Accessory
   Please use our recommended accessory. Or it will damage the projector.
3. Correct environment
   Do not place the projector in a wet environment, like damp basement or near the swimming pool, etc.
4. Ventilation
   The ventilation is equipped for the projector to work stably. Do not put anything around the vents. Or it will cause the projector heating up.
5. Power
   Please make sure the power is within the required power range.
6. Thunder
   For thunder day, please unplug the power cable from the projector.
7. Repair
   Due to high voltage inside, please do not open or try to repair the projector by yourself. Please ask a professional technician to repair the projector.
8. Keep away from heat device
   Please make sure the projector is far away from any heat devices which will damage the projector.

Accessories

Projector*1	Remote Controller*1	Projector Support Base*1
Projector case *1	Power Cable*1	User Manual*1
Lens Cover*1	AV Cable*1
Projector*1	AV Cable*1	Power Cable*1
Remote Controller*1	User Manual*1	Projector Support Base*1

Projector Overview

1. 3.5mm audio output
2. AV port
3. HDMI port
4. USB port*2
5. IR receiver
6. Speaker
7. Ventilation inlet

Note: please refer to the product appearance, this figure is for reference only.

Control Panel

Remark: The adjustable support base can assure the max projection angle by 15°, The best display effect will be obtained by projection angle of 0°~ 8°.

Remote control

Note

1. While using the remote control, point it toward IR receiver.
2. The remote control doesn't come with the battery, required 2*AAA batteries.
3. To avoid battery leakage corrision, please take the batteries out if not use it for a long time.

Specifications

Projection size chart

Optimum projection distance: 2.5m

Focus and Keystone Correction

Two steps to get clear images:

1. Adjust the keystone correction to make picture rectangle.
   
2. Adjust the focus ring to make the picture clear.
   

Focus

Trapezoid correction

Note: It is normal when sharpness in the central, blur in the 10% edge for the lcd projector, due to the keystone correction function.

Signal source menu operation

Before using the projector to play videos, please press"S"through remote control and choose the corresponding signal source to confirm.

Connecting with Smartphones and Ipad

Wireless Connection PS:

1. The fluency of screen mirroring with wireless connection will be affected by the network environment. A bandwidth of 100Mbit or more is recommended when using screen mirroring. Make sure your mobile device is closed to the projector when using wireless connection. A distance within 1 meter is recommended.
2. Because of HDCP limit, when connecting with smartphone, it can't display netflix, hulu and disney.

For iOS system

Method 1: Setting with cellular data

1. Turn on the projector, select "Screen Mirroring" as the input source. It will enter the interface of Screen Mirroring for iOS system. See below.
   
2. Go to the settings of your iOS mobile device and connect it to the Wi-Fi of RKcast-XXXXXX (password: 12345678). Please ignore the exclamation mark before it.
3. Swipe up the screen of your iOS mobile device, then tap Screen Mirroring/AirPlay Mirroring and search for the projector.
   

Method 2: Setting with Home Wifi

1. Select RKcast-XXXXXX from the searching results to connect. Wi-Fi of RKcast-XXXXX (password: 12345678)
2. Visit 192.168.XX.XX (please put in the IP showed on the screen) from a browser on your mobile device, tap WiFi AP >Scan, select your router's Wi-Fi and enter the right password, then tap Connect to continue.
   
3. Your router' s Wi-Fi will be displayed on interface of Screen. See below.
   
4. Get back to the Wi- Fi setting of your iOS mobile device, then connect it to the same router's Wi-Fi.
5. Swipe up the screen of your iOS mobile device and tap "Screen Mirroring" to search for the projector, then select RKcast-XXXXX from the searching results to connect.

For Android System

To activate this function, your android device must support Multi-Screen/Wireless display.

Names may differ from different devices.

Method 1: Setting with cellular data

1. Turn on the projector, select "Screen Mirroring" as the Input Source, then choose Android on the projector interface of Screen Mirroring for Android System.
   
2. Turn on the Wi-Fi Switch in your Android device.
3. Select RKcast-XXXXXX from the searching results to connect. Password is 12345678.
4. Activate Multi-Screen function in your Android device and then it will work.

Method 2: Setting with Home Wifi

1. Select RKcast-XXXXXX from the searching results to connect. Wi-Fi of RKcast-XXXXX (password: 12345678)
2. Visit 192.168.XX.XX(please put in the IP showed on the screen) from a browser on your mobile device, tap WiFi AP >Scan, select your router's Wi-Fi and enter the right password, then tap Connect to continue.
   
3. Your router' s Wi-Fi will be displayed on interface of Screen. See below.
   Mi 10
4. Get back to the Wi- Fi setting of the android phone, then connect it to the same router's Wi-Fi.
5. Activate Multi-Screen function in your Android device to search for the projector, then select RKcast-XXXXX from the searching results to connect.

Connecting with Bluetooth Speaker

Go into the Menu--Sound---Audio output, under "Static" model to search the bluetooth device.

Connecting with PC, TV stick ect. via HDMI port

1. Connect projector with PC by HDMI cable.
2. Choose the media signal channel:"HDMI"

PS: To connect with macbook, an external HDMI to type C cable is needed.

Here has the setting in the laptop when connecting the projector (Fn+ F* [function key])

Connecting with Sound bar

1. Use the 3.5mm audio cable to connect with sound bar.
2. Turn on the projector and the sound bar. Then it will work.
3. More details, please contact seller at support@wimius.com.

Connecting with DVD

1. Use the AV cable coming with the projector to connect with DVD.
2. Turn on the projector and DVD player.

USB Multimedia Connecting

1. Insert the USB drive to corresponding interface.
2. Choose the video or picture to play.

PS: the projector only supports USB 2.0 stick, and 1080P 30FPS video. the USB Drive file system must to be FAT32/NTFS, no exFAT

Multimedia File Specification

Image Format

Audio Format

Doesn't support: Dolby AC3/AAC, DTS, WMA, DivX, VC1, RM, RMVB, FLV, etc

Video Format (Bit Rate up to 30~40 Mbs)

Doesn't support: MSVC/CRAM, MP42, GMC, IV32, RLE, cvid, RV20, DivX, RM, RMVB, VC1, FLV, etc

Installing the projector

Ceiling mount
There is a hole in the bottom of the projector for ceiling mount.

Main Function of the Menu

Picture Menu

Picture Mode: Only under mode " User" we could change the Contrast/Brightness/Color/Sharpness of the picture.

Sound Menu

Note:
In the Sound mode "User" interface, you can adjust the "Treble/Bass" of the image by using the +- button on the remote control in the "0-100" range.
Audio Output, you can search the external speaker to connect via the static mode.

Time Menu

Sleep Timer: You can use this function to set the sleep time of the projector. Time adjustment range "OFF/10min/20min/30min/60min/90min/120min/180min/240min"

Option Menu

FAQ