Toshiba e-studio200l Service Manual page 44

Error code Classification
C940 Circuit related ser-
vice call
C970 Process related
service call
CA10 Laser optical unit
related service call
CA20
CB10 Finisher related
service call
CB20
CB30
CB50
CB60
CB80
CC30
CC50
CC60
CC80
CC90
CCA0
CCB0
e-STUDIO200L/202L/230/232/280/282 ERROR CODE AND SELF-DIAGNOSTIC MODE
Contents
Engine-CPU abnormality
High-voltage transformer abnormality: Leakage of the
main charger is detected.
Polygonal motor abnormality: The polygonal motor is not
rotating normally.
H-Sync detection error: H-Sync detection PC board can-
not detect laser beams.
Transport motor abnormality: The transport motor or
stack transport roller is not rotating normally. [MJ-1025]
Delivery motor abnormality: Delivery motor or delivery
roller is not rotating normally. [MJ-1022/1025]
Tray lift motor abnormality: The tray lift motor is not rotat-
ing normally or the delivery tray is not moving normally.
[MJ-1025]
Staple motor (staple/fold) abnormality: The staple motor
is not rotating normally or the stapler is not moving nor-
mally. [MJ-1025]
Stapler unit shift motor abnormality: The stapler unit shift
motor is not rotating normally or the Stapler Unit is not
moving normally. [MJ-1025]
Backup RAM data abnormality:
1) Abnormality of checksum value on finisher controller
board is detected when the power is turned on.
[MJ-1025]
2) Abnormality of checksum value on punch controller
board is detected when the power is turned on.
[MJ-1025 (when MJ-6005 is installed)]
Stack processing motor abnormality: The stack process-
ing motor is not rotating normally or the stack delivery belt
is not moving normally. [MJ-1022]
Paddle motor abnormality: The paddle motor is not rotat-
ing normally or the swing guide is not moving normally.
[MJ-1025]
Horizontal registration motor abnormality: The horizontal
registration motor is not rotating normally or the puncher
is not moving normally.
[MJ-1025 (when MJ-6005 is installed)]
Punch motor abnormality: The punch motor is not rotating
normally or the puncher is not moving normally.
[MJ-1025 (when MJ-6005 is installed)]
Front jogging motor abnormality: Front jogging motor is
not rotating normally or the front alignment plate is not
moving normally. [MJ-1022]
Alignment motor (front) abnormality: The alignment motor
(front) is not rotating normally or the front alignment plate
is not moving normally. [MJ-1025]
Upper stack tray lift motor abnormality: The upper stack
tray lift motor is not rotating or the upper stack tray is not
moving normally. [MJ-1022]
Lower stack tray lift motor abnormality: The lower stack
tray lift motor is not rotating or the lower stack tray is not
moving normally. [MJ-1022]
Rear jogging motor abnormality: Rear jogging motor is
not rotating normally or the rear alignment plate is not
moving normally. [MJ-1022]
Alignment motor (rear) abnormality: The alignment motor
(rear) is not rotating normally or the rear alignment plate
is not moving normally. [MJ-1025]
2 - 8
Troubleshooting
P. 5-76
P. 5-76
P. 5-60
P. 5-60
P. 5-61
P. 5-62
P. 5-63
P. 5-64
P. 5-66
P. 5-67
P. 5-67
P. 5-69
P. 5-69
P. 5-70
P. 5-71
P. 5-72
P. 5-73
June 2004 © TOSHIBA TEC