Troubleshooting - Yamaha MCX-2000 Owner's Manual

Troubleshooting
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is
not listed below or if the instruction below does not help, set this unit to the standby mode, disconnect the
power cord, and contact the nearest authorized YAMAHA dealer or service center.
Problem Cause Remedy Refer to
page
Auto Configuration The network is not configured correctly. Check the network settings of the MusicCAST client 21- 34
does not appear to and MusicCAST server.
work correctly.
The network signal is weak (for wireless Try changing the network channel or the location of 21- 34
network connections only). the MusicCAST client, or alternatively changing to a
wired network connection.
Either the MusicCAST server or the Check the configuration procedure and try again. 21- 34
MusicCAST client is not set to Auto
Configuration mode.
The MusicCAST server is storing songs Stop recording and start the Auto Configuration MCX-
or recording. process again. 1000
owner's
manual,
page 21
The MusicCAST client
The volume setting of the MusicCAST Increase the volume setting.
10, 12, 13
does not output any client is low.
sound.
The MusicCAST client is not correctly Check the connections between the MusicCAST 11,20
connected to speakers. client and the speakers.
You cannot start Auto Configuration is not complete. Run the Auto Configuration process.
26,27
playback on the
MusicCAST client. The network is not configured correctly. Check the network settings of the MusicCAST client 21-34
and MusicCAST server.
The MusicCAST server is turned off. Turn the MusicCAST server on. 20
The hard disk drive in the MusicCAST Wait until the MusicCAST server completes MCX-
server does not contain any songs that encoding songs to MP3. 1000
have been completely. encoded to MP3
Register songs stored from external components to owner's
format. the library, or wait for the MP3 encoding process to
manual,
complete. page 121
When the MusicCAST server is set to The "*" displayed beside PCM-only songs disappears
MCX-
distribute MP3 files to your MusicCAST when encoding is complete. 1000
client, the MusicCAST client displays a owner's
"*"
beside songs which the MusicCAST manual,
server has not converted to MP3 format. page 121
The network signal is weak (for wireless Try changing the network channel or the location of
21- 34
network connections only). the MusicCAST client, or alternatively changing to a
wired network connection.
The network signal is weak (for wireless Try changing the network channel or the location of 21- 34
network connections only). the MusicCAST client, or alternatively changing to a
wired network connection.
Playback from the The network is extremely congested (for Place your MusicCAST clients under an independent 21- 34
MusicCAST client wired network connections only). subnet mask, or upgrade your network hardware.
skips.
•
»
"'C
"'C
CD
:::::s
c.
;<"
Troubleshooting
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is
not listed below or if the instruction below does not help, set this unit to the standby mode, disconnect the
power cord, and contact the nearest authorized YAMAHA dealer or service center.
Problem Cause Remedy Refer to
page
Auto Configuration The network is not configured correctly. Check the network settings of the MusicCAST client 21- 34
does not appear to and MusicCAST server.
work correctly.
The network signal is weak (for wireless Try changing the network channel or the location of 21- 34
network connections only). the MusicCAST client, or alternatively changing to a
wired network connection.
Either the MusicCAST server or the Check the configuration procedure and try again. 21- 34
MusicCAST client is not set to Auto
Configuration mode.
The MusicCAST server is storing songs Stop recording and start the Auto Configuration MCX-
or recording. process again. 1000
owner's
manual,
page 21
The MusicCAST client
The volume setting of the MusicCAST Increase the volume setting.
10, 12, 13
does not output any client is low.
sound.
The MusicCAST client is not correctly Check the connections between the MusicCAST 11,20
connected to speakers. client and the speakers.
You cannot start Auto Configuration is not complete. Run the Auto Configuration process.
26,27
playback on the
MusicCAST client. The network is not configured correctly. Check the network settings of the MusicCAST client 21-34
and MusicCAST server.
The MusicCAST server is turned off. Turn the MusicCAST server on. 20
The hard disk drive in the MusicCAST Wait until the MusicCAST server completes MCX-
server does not contain any songs that encoding songs to MP3. 1000
have been completely. encoded to MP3
Register songs stored from external components to owner's
format. the library, or wait for the MP3 encoding process to
manual,
complete. page 121
When the MusicCAST server is set to The "*" displayed beside PCM-only songs disappears
MCX-
distribute MP3 files to your MusicCAST when encoding is complete. 1000
client, the MusicCAST client displays a owner's
"*"
beside songs which the MusicCAST manual,
server has not converted to MP3 format. page 121
The network signal is weak (for wireless Try changing the network channel or the location of
21- 34
network connections only). the MusicCAST client, or alternatively changing to a
wired network connection.
The network signal is weak (for wireless Try changing the network channel or the location of 21- 34
network connections only). the MusicCAST client, or alternatively changing to a
wired network connection.
Playback from the The network is extremely congested (for Place your MusicCAST clients under an independent 21- 34
MusicCAST client wired network connections only). subnet mask, or upgrade your network hardware.
skips.
•
»
"'C
"'C
CD
:::::s
c.
;<"