Specifications - Sony DFS-700 Service Manual

Specifications

Specifications
General
Signaling system DFS-700: NTSC
DFS-700P: PAL
Power requirements
DFS-700: 100 V AC, 50/60 Hz
DFS-700P: 220/240 V AC,
50/60 Hz
Operating voltage DFS-700: 90 to 130 V AC, 47 to
63 Hz
DFS-700P: 180 to 260 V AC, 47 to
63 Hz
Power consumption
200 W
Peak inrush current
(1) Power ON, current probe method: 24 A (240 V)
(2) Hot switching inrush current, measured in
accordance with European
standard EN55103-1:13 A
(230 V)
Operating temperature
0°C to 40°C (32°F to 104°F)
Control panel: 440 × 121 × 287 mm
Dimensions
× 4 × 11
(w/h/d) (17 3 7 3
/ / /
8 8 8
inches)
Processor: 440 × 133 × 520 mm
× 5 × 20
3 1 1
(w/h/d) (17 / / /
8 4 2
inches)
Mass Control panel: Approx. 3 kg
(6 lb 9 oz)
Processor unit: Approx. 14 kg
(30 lb 13 oz)
Signal processing
Sampling rate Y: 13.5 MHz, R–Y/B–Y:
6.75 MHz, KEY: 13.5 MHz
Quantizing Y/R–Y/B–Y: 8 bits, KEY: 8 bits
Linearity (composite output)
Differential gain
Less than 3.5% (composite input)
Less than 2% (component, S-Video
input)
Differential phase
Less than 2.5º (composite input)
Less than 1.0º (component,
S-Video input)
Frequency response
0 to 5 MHz + 0.5 dB/–1 dB
A-64
Appendixes
S/N More than 50 dB (composite)
More than 55 dB (component,
S-Video)
System delay 1 frame
Preread mode: Background bus
only 4H
Input signals
VIDEO INPUT
COMPONENT
BNC type (Y/R–Y/B–Y ) × 4
(with BKDF-701: × 8)
Y: 1.0 Vp-p, 75 ohms
R–Y/B–Y: 0.756 Vp-p, 75 ohms
RGB To use some of the above
COMPONENT connectors.
R/G/B: 0.756 Vp-p, 75 ohms,
sync on green
COMPOSITE (with BKDF-702/702P)
BNC type × 4
VIDEO: 1.0 Vp-p, 75 ohms,
sync negative
S-VIDEO (with BKDF-702/702P)
DIN × 4
Y: 1.0 Vp-p, 75 ohms, sync
negative,
C (BURST): 0.286 Vp-p, 75 ohms
BNC type × 2, loop through
REF. VIDEO
SYNC: 0.286 Vp-p
BURST: 0.286 Vp-p
BNC type × 4 (with BKDF-701:
SDI INPUT
× 8)
270 Mb/s, compliant with SMPTE-
259M
BNC type × 2, loop through
DSK KEY IN
1.0 Vp-p, 75 ohms, sync negative
Output signals
PGM OUT
BNC type × 2
SDI
270 Mb/s, compliant with SMPTE-
259M
COMPONENT BNC type (Y/R–Y/B–Y ) × 2
Y: 1.0 Vp-p, 75 ohms, sync
negagive
R–Y/B–Y: 0.756 Vp-p, 75 ohms
COMPOSITE BNC type × 2
Video: 1.0 Vp-p, 75 ohms,
sync negative
DIN × 2
S-VIDEO
Y: 1.0 Vp-p, 75 ohms, sync
negative
C (BURST): 0.286 Vp-p, 75 ohms
BNC type × 1
CLEAN OUT
SDI: 270 Mb/s, compliant with
SMPTE-259M
BLACK BURST OUT
BNC type × 3
SYNC: 0.286 Vp-p
BURST: 0.286 Vp-p
Control signals
D-sub, 9-pin × 1 (RS-422A)
EDITOR
BNC type × 2, TTL level, active
GPI T 1/2
low
D-sub, 25-pin × 1
PANEL
D-sub, 25-pin × 1, relay contact
TALLYL
output × 8
USB × 1
TERMINAL
Recommended equipment and cables
Editing control unit
PVE-500, BVE-900/910/2000,
BVE-600
VTR DSR-2000/2000P, DNW-75/75P
Audio mixer SRP-V200R
Cables RCC-5G/10G/30G 9-pin remote
control cables
Supplied accessories
AC power cord (1)
25-pin control cable, 10 m (1)
Button labels (1 set)
Tool for removing key tops (1)
Operation manual (1)
Design and specifications subject to change without
notice.
A-65
Appendixes