Table of Contents
Advertisement
MEX-M72BT/N5300BT/N7300BD
Pin No.
Pin Name
51
RESB
52
SIFCK
53
SIFDI
54
SIFDO
55
SIFCE
56
BUSYB
57
CD_BUSYB
58
LACK
59
BCK
60
DATA
61
MCLK
62
USB_IN
63
NC
64
GP46
65
NC
66
DVSS
67
DVDD
68
UDM2
69
UDP2
70
DVSS
71
UDM1
72
UDP1
73
XVDD
74
XIN
75
XOUT
76
XVSS
77
AFILT
78
NC
79
VVDD2
80
DVSS
81
DVDD
82
CP_SCL
83
CP_SDA
84
CP_RESET (NC)
85
CD_RESB
86
CMD_ERR
87
DVDD12_1
88
DVDD
89
DVSS
90
DVDD18_1
91
JTRSTB
92
JTCK
93
JTDI
94
JTMS
95
JTDO
96
JTRTCK
97
LFOUT
98
LROUT
99
LVRIN
100
DACOUTL
63
I/O
I
Reset signal input from the system controller
I
Serial data transfer clock signal input from the system controller
I
Serial data input from the system controller
O
Serial data output to the system controller
I
Chip enable signal input from the system controller
O
Busy signal output to the system controller
I
Busy signal input from the digital servo processor
I
L/R sampling clock signal input from the digital servo processor
I
Bit clock signal input from the digital servo processor
I
Audio data input from the digital servo processor
I
Master clock signal input from the digital servo processor
O
USB device detection signal output to the system controller
I/O
Not used
I/O
Not used
I/O
Not used
-
Ground terminal (for digital system)
-
Power supply terminal (+3.3V) (for digital system)
I/O
Two-way Bluetooth data (–) bus with the BT module
I/O
Two-way Bluetooth data (+) bus with the BT module
-
Ground terminal (for digital system)
I/O
Two-way USB data (–) bus with the USB connector
I/O
Two-way USB data (+) bus with the USB connector
-
Power supply terminal (+3.3V) (for oscillator)
I
System clock input terminal (12 MHz)
O
System clock output terminal (12 MHz)
-
Ground terminal (for oscillator)
O
Charge pump output terminal (for PLL)
-
Not used
-
Power supply terminal (+3.3V) (for PLL)
-
Ground terminal (for digital system)
-
Power supply terminal (+3.3V) (for digital system)
O
Serial data transfer clock signal output to the EEPROM
I/O
Two-way data bus with the EEPROM
O
Reset signal output terminal
O
Reset signal output to the digital servo processor
O
Command error signal output to the system controller
-
External capacitor connection terminal for internal regulator
-
Power supply terminal (+3.3V) (for digital system)
-
Ground terminal (for digital system)
-
External capacitor connection terminal for internal regulator
I
Reset signal input terminal (for JTAG)
I
Clock signal input terminal (for JTAG)
I
Data input terminal (for JTAG)
I
Mode selection signal input terminal (for JTAG)
O
Data output terminal (for JTAG)
O
Return clock signal output terminal (for JTAG)
O
Audio signal (front L-ch) output to the power amplifi er and FRONT audio out jack
O
Audio signal (rear L-ch) output to the power amplifi er and REAR audio out jack
I
Audio signal (L-ch) input terminal
O
Audio signal (L-ch) output terminal
Description
"L": reset
"L": busy
"L": busy
Not used
"L": reset
"H": error
Normally: fi xed at "L"
Normally: fi xed at "L"
Normally: fi xed at "L"
Normally: fi xed at "H"
Normally: open
Normally: open
Sony CONFIDENTIAL
For Authorized Servicer
"L": USB device is connected
SYS SET
Advertisement
Table of Contents
