External Monitor Output; Configuring The External Monitor Resolution; Configuring Audio Input/Output; Configuring The Usb Connector Input/Output Signal - Kenwood TS-890S Instruction Manual

External Monitor Output

Connecting an external monitor to the DISPLAY connector
enables the image displayed on the screen of this transceiver to
be displayed on the external monitor at the same time.
Configure in Advanced Menu [21] "External
Display"
Setting Value Off/ On (default)

Configuring the External Monitor Resolution

The resolution of the external monitor that is connected to the
DISPLAY connector can be configured.
Configure in Advanced Menu [22] "Resolution
(External Display)"
Setting Value 800 x 600 (default)/ 848 x 480
When the resolution of the external monitor is changed,
●
a resolution switch screen will appear for approximately
5 seconds before the change is applied.

Configuring Audio Input/Output

Configuring the USB Connector Input/Output Signal

The input/output level of the audio signal when an external device
is connected to the (USB-B) connector on the rear panel can be
configured.

Configuring the Audio Signal Input Level

Configure the audio input level for the (USB-B) connector on the
rear panel.
Configure in Menu [7-06] "USB: Audio Input Level"
Setting Value 0 to 50 (default) to 100 (1 step)

Configuring the Audio Signal Output Level

Configure the audio output level for the (USB-B) connector on the
rear panel.
Configure in Menu [7-08] "USB: Audio Output
Level"
Setting Value 0 to 100 (default) (1 step)
When using a Windows PC, wait for the PC to recognize
●
this transceiver, then select Control Panel → Hardware
and Sound → Sound → Recording → Microphone (USB
Audio CODEC) → Properties, followed by selecting "2
channel".
Windows is a registered trademark of Microsoft
●
Corporation in the United States and other countries.
Configuring the ACC 2 Connector Input/Output
Signal
The input/output level of the audio signal when an external device
is connected to the ACC 2 connector on the rear panel can be
configured.
Configuring the Audio Signal Input Level
Configure the level of audio signal input to the ACC 2 connector
on the rear panel.
Configure in Menu [7-07] "ACC 2: Audio Input
Level"
Setting Value 0 to 50 (default) to 100 (1 step)
Configuring the Audio Signal Output Level
Configure the input/output level of the audio signal when an
external device is connected to the ACC 2 connector on the rear
panel.
Configure in Menu [7-09] "ACC 2: Audio Output
Level"
Setting Value 0 to 50 (default) to 100 (1 step)
Configuring the TX Monitor Level for External Audio
Output
Configure the level of the TX monitor audio that is output from the
rear connector.
Configure in Menu [7-10] "TX Monitor Level (Rear
Connectors)"
Setting Value Linked (default)/ 0 to 20 (1 step)
• Configuring to "Linked" changes the level in tandem with the
level configured during TX monitor level adjustment.
Configuring Audio Mixing for the External Audio
Output Connector
Configure whether to mix the audio produced by this transceiver
with the RX audio that is output from the (USB-B) connector and
ANO terminal of the ACC 2 connector.
Configure in Menu [7-11] "Audio Output Type (Rear
Connectors)"
Setting Value All (default)/ Received Audio only
All: Enables output of beep tone, voice guidance, audio of voice
message memory and recorded audio or sidetone.
Received Audio Only: Select this setting when having an
external device decode the digital modulation signals.
• When the RX audio is mixed with the beep tone, voice
guidance or error tone emitted from this transceiver, the
command response or error tone produced by this
transceiver can also be heard at a remote location during,
for example, KNS (KENWOOD NETWORK COMMAND
SYSTEM) operation with this transceiver installed at a
remote location.
Audio output to LAN is used for the purpose of listening
●
to the audio output from the transceiver speaker on a
remote PC during remote operation. As such, audio such
as the beep sound is always mixed regardless of the
setting in this menu.
OTHER FUNCTIONS 16
16-7