Kenwood TS-890S Instruction Manual page 138

13 VOICE GUIDANCE
Screen
Selection of file to read
Selection of data to read
(DATA)
Processing (without
CANCEL key)
Data reading complete
Request to get ready the
USB flash drive
Data saving complete
TX audio source input
settings
VOX level configuration
TX output power limiter
configuration
Speech processor
configuration
13-4
Operation/Status
When the RXEQ screen is
displayed or when [VOICE1] is
pressed
When the TXEQ screen is
displayed or when [VOICE1] is
pressed
When the DATA screen is
displayed or when [VOICE1] is
pressed
When a selection is made
When the file deletion
confirmation screen is
displayed or when [VOICE1] is
pressed
Name editing
When the file browsing location
is changed
When screen is displayed or
when [VOICE1] is pressed
When a selection is made
(environment-dependent)
When a selection is made (CW) "CW" + "Message" + [On/ Off]
When a selection is made (voice
message)
Switching between ON/OFF
When screen is displayed or
when [VOICE1] is pressed
When screen is displayed or
when [VOICE1] is pressed
When screen is displayed or
when [VOICE1] is pressed
When screen is displayed or
when [VOICE1] is pressed
When screen is displayed or
when [VOICE1] is pressed
Switching method of
transmission
Specification of audio input line
(Front/Rear) (</>)
Front input selection F4
[SELECT]
Rear input selection F4
[SELECT]
Switching DATA VOX between
ON/OFF
When screen is displayed or
when [VOICE1] is pressed
Switching of audio source input [Mic./ ACC two/ USB/ LAN]
Switching the parameter to
configure
Increasing or decreasing the
setting value
Reset to default value
When screen is displayed or
when [VOICE1] is pressed
TX output power type selection [TX power + Limit + [SSB/ CW/ FSK PSK/ FM AM/ Data] / TX Tune]
Band selection
Increasing or decreasing TX
output power
Reset to default value
When screen is displayed or
when [VOICE1] is pressed
Effect selection
Switching between "Input" and
"Output"
Increasing or decreasing the
value
Content of Announcement
"File" + "List" + "RX" + "Equalizer"
"File" + "List" + "TX" + "Equalizer"
"File" + "List" + "Data"
Year + Month + Day + Time (Announces the time stamp of the file)
"Delete" + "Are you Sure?"
"Edit"
[USB/ Internal]
"Read" + "Data" + "Selection"
"ENV" + [On/ Off]
"Voice" + "Message" + [On/ Off]
[On/ Off]
"Please wait" (Announcement is not output when reading data with RXEQ/TXEQ.)
"Completed"
"USB" + "Connect"
"Completed"
"Moduration-Source" + [Mic. + PTT/ Data + PTT]
[Mic. + PTT/ Data + PTT]
[F/ R]
[Off/ Mic.]
[Off/ ACC 2/ USB/ LAN]
"Data" + "VOX" + [Off/ ACC two/ USB/ LAN]
[VOX gain/ Anti- + VOX gain/ VOX delay] + [Mic./ ACC two/ USB/ LAN] + Value
[VOX gain/ Anti- + VOX gain/ VOX delay]
Value
No announcement
[TX power + Limit + [SSB/ CW/ FSK PSK/ FM AM/ Data]/ [TX Tune] + Band + Value
The band is [1.8/ 3.5/ 5/ 7/ 10/ 14/ 18/ 21/ 24/ 28/ 50] + "Mega Hertz"
[1.8/ 3.5/ 5/ 7/ 10/ 14/ 18/ 21/ 24/ 28/ 50/ 70] + "Mega Hertz"
Value
No announcement
"Processor" + [Soft/Hard] + [In/Out] + Value
[Soft/ Hard]
[In/ Out]
Value