Related Manuals for Bosch NDP-45A2-Z12C
Summary of Contents for Bosch NDP-45A2-Z12C
- Page 1 AUTODOME IP 4000i NDP‑4502‑Z12│NDP‑4502‑Z12C│NDP‑45A2‑Z12C│NDP‑45A2‑Z1 Installation Manual...
-
Page 3: Table Of Contents
Installing a Pipe Mount and Camera 11.1 Tools Required 11.2 Installation Requirements 11.3 Preparing the Ceiling for Installation 11.4 Installing the Pipe Mount 11.5 Attaching the Camera to the Pendant Interface Plate Connection Decommissioning Bosch Security Systems Installation Manual 2020-05 | 2.0 |... -
Page 4: Safety
Legal information Copyright This manual is the intellectual property of Bosch Security Systems, Inc. and is protected by copyright. All rights reserved. Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly. -
Page 5: Connection In Applications
PoE: Use only approved PoE+ devices. Power-over-Ethernet can be connected at the same time as a 24 VAC power supply. If auxiliary power (24 VAC) and PoE+ are applied simultaneously, the camera selects auxiliary input and shuts off PoE+. Bosch Security Systems Installation Manual 2020-05 | 2.0 |... -
Page 6: Customer Support And Service
| Safety AUTODOME IP 4000i Customer support and service If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and shipping instructions. Telephone: 800-366-2283 Fax: 800-366-1329 Email: cctv.repair@us.bosch.com Customer Service Telephone: 888-289-0096 Fax: 585-223-9180 Email: security.sales@us.bosch.com... -
Page 7: Introduction
Sales or Customer Service Representative from Bosch Security Systems. – Do not use this product if any component appears to be damaged. Please contact Bosch Security Systems in the event of damaged goods. – The original packing carton (if undamaged) is the safest container in which to transport the unit and must be used if returning the unit for service. -
Page 8: Product Description
The camera’s aesthetic design and flexible mounting options allow unobtrusive surveillance of large halls, reception areas, or waiting areas that would otherwise require multiple cameras for effective surveillance. 2020-05 | 2.0 | Installation Manual Bosch Security Systems... -
Page 9: Preparing Wiring
28 m (94 ft) 45 m (150 ft) 72 m (238 ft) 183 m (603 ft) Wire Gage Note: Metric wire sizes are standard DIN sizes, ISO6722, mm². Wire diameter (mm²) Bosch Security Systems Installation Manual 2020-05 | 2.0 |... -
Page 10: Preparing The Camera
For in-ceiling models, use T10. Loosen the three (3) Hex screws in the trim ring / bubble enclosure with the appropriate Torx screwdriver. Remove the trim ring / bubble enclosure. 3× 2020-05 | 2.0 | Installation Manual Bosch Security Systems... - Page 11 AUTODOME IP 4000i Preparing the Camera | en 3× Remove the foam insert that protects the camera block. Remove the tape holding the plastic lens protector; remove the lens protector. Bosch Security Systems Installation Manual 2020-05 | 2.0 |...
-
Page 12: Installing A Microsd Card (Optional)
Insert the card into the slot (item 2 in the following figure). Push the camera block into its original position (item 3 in the following figure). Note: The next two steps are for pendant models only. 2020-05 | 2.0 | Installation Manual Bosch Security Systems... - Page 13 AUTODOME IP 4000i Installing a microSD card (optional) | en Replace the trim ring / bubble enclosure. Tighten the screws with the T15 Torx screwdriver. 3× Bosch Security Systems Installation Manual 2020-05 | 2.0 |...
-
Page 14: Installing A Surface Mount And Camera
Drill the four (4) holes in the installation location. Attach the surface mount adapter to the surface using the four screws. 2020-05 | 2.0 | Installation Manual Bosch Security Systems... - Page 15 Attach the mounting plate (supplied with the camera) to the surface mount adapter with the three (3) M4 – .7 x 8 Phillips pan head machine screws (supplied with the surface mount adapter). Bosch Security Systems Installation Manual 2020-05 | 2.0 |...
- Page 16 | Installing a Surface Mount and Camera AUTODOME IP 4000i 3× 2020-05 | 2.0 | Installation Manual Bosch Security Systems...
-
Page 17: Installing An In-Ceiling Camera In A Suspended Ceiling
Base Plate Bar Clips Use the bracket Base Plate as a template or cut a hole-sized hole in the center of the ceiling tile with a drywall utility saw or jig saw. Bosch Security Systems Installation Manual 2020-05 | 2.0 |... - Page 18 Tighten the four (4) securing screws to the Bracket Assembly. Figure 8.3: Tighten Bracket Securing Screw Secure the Bracket Assembly to an overhead securing point with a safety wire. Figure 8.4: Secure Bracket Assembly 2020-05 | 2.0 | Installation Manual Bosch Security Systems...
-
Page 19: Securing The Camera To The Ceiling
Insert the camera (without the trim ring / bubble enclosure) into the hole in the ceiling. Ensure not to pinch the cables. Turn each fastening screw to secure the clamps in the ceiling. Bosch Security Systems Installation Manual 2020-05 | 2.0 |... - Page 20 Place the trim ring / bubble enclosure in position over the camera block, aligning the three (3) screws. Tighten the screws firmly to secure the trim ring / bubble enclosure to the in-ceiling bracket. 2020-05 | 2.0 | Installation Manual Bosch Security Systems...
- Page 21 AUTODOME IP 4000i Installing an In-ceiling Camera in a Suspended Ceiling | en 3× Bosch Security Systems Installation Manual 2020-05 | 2.0 |...
-
Page 22: Installing An In-Ceiling Camera In A Drywall Ceiling
Cut the hole in the ceiling with a drywall utility saw or jig saw. > 15 kg (33 lb) 178.0 (7.0) Pull the cables (24 VAC, CAT 5/CAT6, alarm and/or audio as needed) through the hole in the ceiling. 2020-05 | 2.0 | Installation Manual Bosch Security Systems... -
Page 23: Securing The Camera To The Ceiling
Installing an In-Ceiling Camera in a Drywall Ceiling | en Securing the Camera to the Ceiling Connect the cables from the ceiling to the cables on the camera. Refer to the chapter Connection for more information. Bosch Security Systems Installation Manual 2020-05 | 2.0 |... - Page 24 Place the trim ring / bubble enclosure in position over the camera block, aligning the three (3) screws. Tighten the screws firmly to secure the trim ring / bubble enclosure to the in-ceiling bracket. 2020-05 | 2.0 | Installation Manual Bosch Security Systems...
- Page 25 AUTODOME IP 4000i Installing an In-Ceiling Camera in a Drywall Ceiling | en 3× Bosch Security Systems Installation Manual 2020-05 | 2.0 |...
-
Page 26: Installing A Camera Directly To An Indoor Wall
Attach an M5 screw and the L-shaped end of the safety tether to the stand-off on the pendant interface plate mount with the T25 Torx screwdriver. Attach the M4 screw to the ground point on the pendant interface plate mount with the T25 Torx screwdriver. 2020-05 | 2.0 | Installation Manual Bosch Security Systems... - Page 27 (3) M4 screws. Orient the plate as indicated in the following figure. 3× Attach the hook of the safety tether from the adapter to the bottom of the camera. Bosch Security Systems Installation Manual 2020-05 | 2.0 |...
- Page 28 10. Rotate the camera approximately 15 degrees in a clockwise direction to lock firmly into place. 11. Secure the safety locking screw with the T10 Torx screwdriver. 2020-05 | 2.0 | Installation Manual Bosch Security Systems...
- Page 29 AUTODOME IP 4000i Installing a Camera Directly to an Indoor Wall | en ≈15° Bosch Security Systems Installation Manual 2020-05 | 2.0 |...
-
Page 30: Installing A Pipe Mount And Camera
Attach the mounting flange and (adapter) to the direct connect plate using four M5 screws. Thread the cables through the pipe mount. Attach the pipe mount to the mounting flange and (adapter). 2020-05 | 2.0 | Installation Manual Bosch Security Systems... -
Page 31: Attaching The Camera To The Pendant Interface Plate
Attach the metal mounting plate to the inside of the pendant interface plate mount with the three (3) M4 screws. Orient the plate as indicated in the following figure. Bosch Security Systems Installation Manual 2020-05 | 2.0 |... - Page 32 Attach the hook of the safety tether from the adapter to the bottom of the camera. Connect the mating connectors from the user-supplied cables from the ceiling to the matching connectors from the camera. Refer to the chapter Connection, page 34 for more information. 2020-05 | 2.0 | Installation Manual Bosch Security Systems...
- Page 33 10. Rotate the camera approximately 15 degrees in a clockwise direction to lock firmly into place. 11. Secure the safety locking screw with the T10 Torx screwdriver. ≈15° Bosch Security Systems Installation Manual 2020-05 | 2.0 |...
-
Page 34: Connection
4 Network device (computer with monitor, DVR/NVR, etc.) If desired, connect the alarm and/or audio wires as identified in the following table. Label ID Description Cable Wire Color ALARM_COM Alarm Communications Red ALARM_OUT Alarm Out Brown 2020-05 | 2.0 | Installation Manual Bosch Security Systems... - Page 35 Description Cable Wire Color ALARM_IN1 Alarm In 1 White ALARM_IN2 Alarm In 2 Blue AUDIO OUT Audio Out Grey Ground Black AUDIO GND Audio Ground Green AUDIO IN Audio In Purple Bosch Security Systems Installation Manual 2020-05 | 2.0 |...
-
Page 36: Decommissioning
| Decommissioning AUTODOME IP 4000i Decommissioning 2020-05 | 2.0 | Installation Manual Bosch Security Systems... - Page 37 AUTODOME IP 4000i Decommissioning | Bosch Security Systems Installation Manual 2020-05 | 2.0 |...
- Page 38 | Decommissioning AUTODOME IP 4000i 2020-05 | 2.0 | Installation Manual Bosch Security Systems...
- Page 40 Bosch Security Systems B.V. Torenallee 49 5617 BA Eindhoven Netherlands www.boschsecurity.com © Bosch Security Systems B.V., 2020...