Installation Of Software; Dme-3000; Dme-7000 - Sony DME-7000 Maintenance Manual

1-16. Installation of Software

The CPU programs of DME-3000/7000 and BKDM-3010
are installed in flash memory that can be electrically erased
from a floppy disk. Therefore, ROM replacement is not
required when updating.
A CPU program has already been installed at the factory.
However, the installed CPU program may be old in version
level. Be sure to install the software according to the
following procedures.

1-16-1. DME-3000

Software Installation
Install the operation software for the processor in accor-
dance with the following procedures.
m
• If there is effects data stored in DME-3000 registers, the
operation of installing the software will cause the data to
be destroyed. Before beginning the installation opera-
tion, save the contents of registers to floppy disk.
(For details of saving to floppy disk, refer to the optional
User's Guide BZDM-3020.)
• If using optional boards, complete the installation of the
optional boards before installing the software. If you
add optional boards after installing the software, install
the software again.
[Procedures]
1. Insert the floppy disk labeled "SYSTEM DISK 2" of
BZDM-3020 in the floppy disk drive of BKDM-3010.
2. With the third set of soft key indications shown in the
SETUP & DIAG menu, press "F4" (INSTALL) to
display the INSTALL menu.
3. Press the channel button (CH1 or CH2) in the channel
selection section of BKDM-3010 for the processor
channel for which you wish to install the software.
4. Press "F1" (INSTALL).
5. To confirm the installation, press "F5" (OK).
To abort the installation, press "F6" (CANCEL).
n
The process takes approximately ten minutes, during
which no other operations are possible.
6. When the installation completes normally, a message
"Finished" displays on the monitor.
n
For details, refer to the optional User's Guide BZDM-
3020.

1-16-2. DME-7000

Software Installation
Install the operation software for the processor in accor-
dance with the following procedures.
m
• If there is effects data stored in DME-7000 registers, the
operation of installing the software will cause the data to
be destroyed. Before beginning the installation opera-
tion, save the contents of registers to floppy disk.
(For details of saving to floppy disk, refer to the optional
User's Guide BZDM-7020.)
• If using optional boards, complete the installation of the
optional boards before installing the software. If you
add optional boards after installing the software, install
the software again.
[Procedures]
1. Change the two blank buttons in the channel selection
section of BKDM-3010 for "CH3" and "CH4" buttons
that is supplied with BZDM-7020.
(Refer to the section 3-4-2.)
2. Insert the floppy disk labeled "SYSTEM DISK 2" of
BZDM-7020 in the floppy disk drive of BKDM-3010.
3. With the third set of soft key indications shown in the
SETUP & DIAG menu, press "F4" (INSTALL) to
display the INSTALL menu.
4. Press the channel button (CH1 to CH4) in the channel
selection section of BKDM-3010 for the processor
channel for which you wish to install the software.
5. Press "F1" (INSTALL).
6. To confirm the installation, press "F5" (OK).
To abort the installation, press "F6" (CANCEL).
n
The process takes approximately ten minutes, during
which no other operations are possible.
7. When the installation completes normally, a message
"Finished" displays on the monitor.
n
For details, refer to the optional User's Guide BZDM-
7020.
1-16. Installation of Software
1-39 (E)