Panasonic WJ-SX 150A Operating Instructions Manual page 199

12. Select the sensitivity by moving the joystick upward or
downward.
The sensitivity will be applied.
OFF: The motion detector is not activated on the
camera channel.
LOW: The sensitivity level is low.
MID: The sensitivity is level is medium.
HIGH: The sensitivity level is high.
13. To exit the motion detection area setup window, press
the CAM (SET) button.
The motion detection mode setup window will be dis-
played on the monitor.
■ VMD SEARCH
ANY AREA
MASKING DURATION
VECTOR
A 20 s B 20
DURATION
A 20 s B 20
SET : [SET] SEARCH : [PLAY]
Notes:
• To cancel the motion detection area setup, press
the MON (ESC) button. The VMD search list window
will be displayed again on the monitor.
• Refer to the unit's operating instructions for details
on each detection mode.
14. Select a desired detection mode with the 3D joystick,
and select a desired parameter by performing either of
the following.
• Rotate the JogDial clockwise or counterclockwise.
• Press the + or – button.
15. Press the CAM (SET) or PLAY/PAUSE button.
The motion detection mode will be determined, and the
VMD search list window will be displayed again on the
monitor.
Notes:
• Refer to Step 2 for the screenshot.
• To cancel the setting and return to the motion
detection area setup window, press the MON (ESC)
or EXIT button.
16. Select a desired recording event by performing one of
the following.
• Move the 3D joystick controller up or down.
• Rotate the JogDial clockwise or counterclockwise.
• Press the + or – button.
Note: To move to the next or previous page, perform
either of the following.
• Move the zoom wheel controller to the right or left.
• Rotate the shuttle ring clockwise or counterclock-
wise.
24H
s C 20 s D
s C 20 s D 20 s
CANCEL : [ESC]
17. Press the PLAY button.
The playback of selected recording event will start.
18. To exit the search mode, press the MON (ESC) or EXIT
button.
The live image will be displayed again on the monitor.
• Marking search
The recording time of the recorded images with a marked
point will be displayed in a list or a thumbnail. For playback,
you will select the desired recording time to play. (Refer to
the recorder's operating instructions for details on marking.)
1. Enter the recorder mode. (Refer to p. 19 Recorder
Mode.)
2. Repeat pressing the SEARCH/T&D SEARCH button
until the marking list window is displayed on the moni-
tor.
The recorder will enter the searching mode.
TIME&DATE CAM
APR.25.03*12:34:56 AM 01ch
APR.25.03*12:34:56 AM 01ch
APR.25.03*12:34:56 AM 01ch
APR.25.03*12:34:56 AM 01ch
APR.25.03*12:34:56 AM 01ch
APR.25.03*12:34:56 AM 01ch
APR.25.03*12:34:56 AM 01ch
APR.25.03*12:34:56 AM 01ch
APR.25.03*12:34:56 AM APR.25.03*12:34:56 AM
TIME&DATE SEARCH REC EVENT SEARCH VMD SEARCH MARK
3. Select the desired marked time by performing one of
the following.
• Move the 3D joystick controller up or down.
• Rotate the JogDial clockwise or counterclockwise.
• Press the + or – button.
Note: To move to the next or previous page, perform
either of the following.
• Move the zoom wheel controller to the right or left.
• Rotate the shuttle ring clockwise or counterclock-
wise.
4. Press the PLAY button.
The playback of selected recording event will start.
5. To exit the search mode, press the MON (ESC) or EXIT
button.
The live image will be displayed again on the monitor.
• Thumbnail window
To change a list (recording event list, VMD search list, or
marking search list) to the thumbnail, press the F1 button.
The monitor display will become as follows.
TOTAL 12345
27