Motor Cable - ABB ACS560 Hardware Manual

86 Electrical installation 86 Electrical installation 86 Electrical installation
1. Attach the residual voltage warning sticker next to the control board.
2. Remove the side plates of the cable box as follows:
Connection procedure, frames R6...R8 Connection procedure, frames R6...R8
Connection procedure, frames R6...R8
76 Electrical installation
• Remove the retaining screws.
WARNING! If the drive will be connected on an IT (ungrounded) system, WARNING! If the drive will be connected on an IT (ungrounded) system,
WARNING! If the drive will be connected on an IT (ungrounded) system,
• Slide the walls out.
make sure you have disconnected the EMC filter and ground-to-phase varistor.
make sure you have disconnected the EMC filter and ground-to-phase varistor. make sure you have disconnected the EMC filter and ground-to-phase varistor.
See page 71. If the drive will be connected on a corner-grounded TN system, make
See page 71. If the drive will be connected on a corner-grounded TN system, make See page 71. If the drive will be connected on a corner-grounded TN system, make
1
sure you have disconnected the EMC filter. See page 71.
sure you have disconnected the EMC filter. See page 71. sure you have disconnected the EMC filter. See page 71.
1. Attach the residual voltage warning sticker next to the control board. 1. Attach the residual voltage warning sticker next to the control board.
1. Attach the residual voltage warning sticker next to the control board.
2. Remove the side plates of the cable box as follows:
2. Remove the side plates of the cable box as follows: 2. Remove the side plates of the cable box as follows:
• Remove the retaining screws.
• Remove the retaining screws. • Remove the retaining screws.
• Slide the walls out. • Slide the walls out. • Slide the walls out.
1
1 1
3. Remove the shroud on the power cable terminals by releasing the clips with a
screwdriver and pulling the shroud out.
3. Remove the shroud on the power cable terminals by releasing the clips with a screwdriver
4. Knock out holes in the shroud for the cables to be installed.
and pulling the shroud out.
5. Frames R8: If you install parallel cables, also knock out holes in the lower shroud
4. Knock out holes in the shroud for the cables to be installed.
3. Remove the shroud on the power cable terminals by releasing the clips with a 3. Remove the shroud on the power cable terminals by releasing the clips with a 3. Remove the shroud on the power cable terminals by releasing the clips with a
screwdriver and pulling the shroud out. screwdriver and pulling the shroud out. screwdriver and pulling the shroud out.
for the cables to be installed.
5. Frames R8: If you install parallel cables, also knock out holes in the lower shroud for
the cables to be installed.
4. Knock out holes in the shroud for the cables to be installed.
4. Knock out holes in the shroud for the cables to be installed. 4. Knock out holes in the shroud for the cables to be installed.
5. Frames R8: If you install parallel cables, also knock out holes in the lower shroud 5. Frames R8: If you install parallel cables, also knock out holes in the lower shroud 5. Frames R8: If you install parallel cables, also knock out holes in the lower shroud
3
for the cables to be installed. for the cables to be installed. for the cables to be installed.
3 3 3
3
3 3 3

Motor cable

6. Cut an adequate hole into the rubber grommet. Slide the grommet onto the cable.
7. Prepare the ends of the input power cable and motor cable as illustrated in the figure. If
you use aluminum cables, put grease to the peeled aluminum cable before connecting it to
the drive. Two different motor cable types are shown in the figures (7a, 7b).
Note:
The bare shield will be grounded 360 degrees. Mark the pigtail made from the shield as a
PE conductor with yellow-and-green color.
2
2
2
2 2
4
4 4
R8...R8
R8
4
5
R8...R8
R8...R8 R8...R8
5
5 5