Mitsubishi Electric FX3G SERIES Programming Manual page 831

FX /FX /FX Series Programmable Controllers
3G 3U 3UC
Programming Manual - Basic & Applied Instruction Edition
Number and name
High-Speed Counter Comparison, High-Speed Table, and Positioning [Positioning is supported in FX
M 8130 HSZ (FNC 55)instruction: Table comparison mode
HSZ (FNC 55)instruction:
[M]8131
Table comparison mode completion flag
HSZ (FNC 55) and PLSY (FNC 57) instructions: Speed
M 8132
pattern mode
HSZ (FNC 55) and PLSY (FNC 57) instructions: Speed
[M]8133
pattern mode completion flag
[M]8134
[M]8135
Not used
[M]8136
[M]8137
HSCT (FNC280) instruction:
[M]8138
Instruction execution complete flag
HSCS(FNC 53), HSCR(FNC 54), HSZ(FNC 55),
[M]8139 HSCT(FNC280) instructions:
High-speed counter comparison instruction executing
ZRN (FNC156) instruction:
M 8140
CLR signal output function enable
[M]8141
[M]8142
Not used
[M]8143
[M]8144
M 8145 [Y000] Pulse output stop command
M 8146 [Y001] Pulse output stop command
[M]8147 [Y000] Pulse output monitor (BUSY/READY)
[M]8148 [Y001] Pulse output monitor (BUSY/READY)
[M]8149 Not used
Inverter Communication Function (Refer to Data Communication Edition for details.)
[M]8150 Not used
[M]8151 Inverter communication in execution [ch1]
*1
Inverter communication error [ch1]
[M]8152
*1
Inverter communication error latch [ch1]
[M]8153
*1
IVBWR (FNC274) instruction error [ch1]
[M]8154
[M]8154 Defined per use of EXTR (FNC180)
[M]8155 EXTR (FNC180) is using communicating port
[M]8156 Inverter communication in execution [ch2]
Communication error or parameter error in EXTR
[M]8156
(FNC180) instruction
Inverter communication error [ch2]
*1
[M]8157
Communication error in EXTR (FNC180) instruction is
latched.
*1
Inverter communication error latch [ch2]
[M]8158
*1
IVBWR (FNC274) instruction error [ch2]
[M]8159
*1. Cleared when PLC switches from STOP to RUN.
*2. Available in Ver. 3.00 or later.
*3. Available in Ver. 1.10 or later.
Operation and function
37 Operation of Special Devices (M8000 -, D8000 -)
37.1 Special Device List (M8000 -, D8000 -)
Applicable model
Correspond-
FX FX FX ing special FX
3G 3U 3UC
device
, FX
3G 1S
–
D8130
–
–
D8131 to
D8134
–
– – – –
– – – –
– – – –
– – – –
– D8138
– D8139
– – – –
– – – –
– – – –
– – – –
– – – –
– – –
– – –
– – –
– – –
– – – –
– – – –
*3
D8151
*3
D8152
*3
D8153
– D8154
– – – –
– – – D8155
*3
D8156
– – – D8156
*3
D8157
– – – D8157
*3
D8158
– D8159
FX FX FX FX
1S 1N 2N 1NC 2NC
, FX , and FX PLCs.]
1N 1NC
– – –
– – –
– – –
– – –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– –
– – – – –
– – – – –
– – – – –
– – – – –
– –
– –
– –
– –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
– – – – –
*2 *2
– – –
*2 *2
– – –
*2 *2
– – –
*2 *2
– – –
– – – – –
– – – – –
829
31
32
33
34
35
36
37
38
A
B