Yamaha CL5 Reference Manual page 85

3.
Use the tabs to select one of the following as the type of item you want to copy.
INPUT Input channel and its parameters
OUTPUT Output channel and its parameters
RACK
GEQ/effect/Premium rack
PATCH/NAME Input/output patch, channel name
DCA DCA group
4.
Select the copy-source channel or parameter.
The view will vary depending on the tab you select.
You cannot select different parameters from different channels.
To select a channel, press the corresponding [SEL] key on the top panel.
• INPUT tab
Select an input channel in the upper left area, and select its parameter in the lower left area.
You can select the following parameters.
ALL
All input channel parameters
INPUT PATCH Input patch settings
NAME Channel name, icon, and channel color
HA
Settings for the head amp assigned to the corresponding input channel
DELAY Input delay settings
HPF HPF settings
DIGITAL GAIN Digital gain settings for the corresponding input channel
EQ EQ settings
DYNA 1 Dynamics 1 settings (including KEY IN SOURCE and KEY IN FILTER)
DYNA 2 Dynamics 2 settings (including KEY IN SOURCE)
MIX SEND Send level, pan, and PRE/POST of the signal sent to a MIX bus
MATRIX SEND Send level, pan, and PRE/POST of the signal sent to a MATRIX bus
FADER Fader level
CH ON On/off status of [ON] keys
INSERT Insert on/off status and insert point
INSERT PATCH Insert in/out patch settings
DIRECT OUT Direct Out on/off, Direct Out level, Direct Out point and patch settings
MIX ON Send on/off to a MIX bus
MATRIX ON Send on/off to a MATRIX bus
TO STEREO Mode, TO ST/TO LCR on/off status, CSR, pan/balance settings
MONO TO MONO on/off status
• OUTPUT tab
Select an output channel in the upper left area, and select its parameter in the lower left area.
You can select the following parameters.
ALL All output channel parameters
OUTPUT PATCH Output patch settings
NAME Channel name, icon, and channel color
EQ EQ settings
DYNA 1 Dynamics 1 settings (including KEY IN SOURCE and KEY IN FILTER)
INSERT Insert on/off status and insert point
INSERT PATCH Insert in/out patch settings
FADER
Fader level
CH ON On/off status of [ON] keys
Mode, TO ST/TO LCR on/off status, CSR, pan/balance settings (MIX 1–
TO STEREO/BAL
24 only)
MONO TO MONO on/off status (MIX 1-24 only)
MATRIX SEND Send level, pan, and PRE/POST of the signal sent to a MATRIX bus
MATRIX ON Send on/off to a MATRIX bus
WITH SEND FROM SEND parameters of the send-source signal that will be sent to a
SOURCE CHs
channel
• RACK tab
Enables you to choose from GEQ RACK, EFFECT RACK, or PREMIUM RACK. You can select
an individual rack for each effect used in dual mode.
• PATCH/NAME tab
You can select the following parameters.
INPUT PATCH All input channel patches, insert in/out patches, Direct Out patches
OUTPUT PATCH All output channel patches, insert in/out patches
INPUT NAME
Channel names, icons, and colors for all input channels
OUTPUT NAME Channel names, icons, and colors for all output channels
HA Analog gain, phantom power on/off status, Gain Compensation settings
CH LINK
Channel link settings
• DCA tab
You can select either ALL or LEVEL/ON. If ALL is selected, all parameters will be copied. If
LEVEL/ON is selected, the master level and [ON] key on/off status will be copied. You can select
copy-source items for each DCA group 1–16 individually.
5.
In the DESTINATION SCENE area, select the range of paste-destination scenes.
Scenes specified between FROM and TO (inclusive) become the paste destination. Use
multifunction knob 7 to specify the FROM value, and multifunction knob 8 to specify the TO
value.
6.
Press the PASTE button.
The selected items of the current scene will be pasted to the scene(s) in memory.
A progress bar will be displayed as the data is being pasted.
During the paste operation, the STOP button will appear. Press the STOP button if you want to
abort the operation. In that case, part of data will be pasted and you will be unable to undo the
operation.
85
Scene memory
Reference Manual