Changing Zones To Entry/Exit; Changing Zones To Inhibited Entry; Changing Zones To Guard; Programming The Date And Time - Texecom Veritas 8 Installation Manual

Veritas 8, 8C & R8 Installation Manual

Changing Zones to Entry/Exit

This suite defines the zones which will be changed into
Entry/Exit zones on the selected part sets. For example the
Control Panel is factory set with Zone 2 included. Thus the
Zone Type of Zone 2 will be changed (from Inhibited Entry)
into Entry/Exit on Part Set 1.
From the Programming Menu, enter
are currently included will indicate.
Zon es
1 2 3 4 5 6 7 8
Press the appropriate numbered button(s) of the
zone(s) to be included or excluded. Press
system will chime to confirm that the new suite has been
accepted. The system will then automatically revert to the
Programming Menu.

Changing Zones to Inhibited Entry

This suite defines the zones which will be changed into
Inhibited Entry zones on the selected part sets. For example
the Control Panel is factory set with no zones included. Thus
no zones will be changed into Inhibited Entry.
From the Programming Menu, enter
are currently included will indicate.
Zon es
1 2 3 4 5 6 7 8
Press the appropriate numbered button(s) of the
zone(s) to be included or excluded. Press
system will chime to confirm that the new suite has been
accepted. The system will then automatically revert to the
Programming Menu.

Changing Zones to Guard

This suite defines the zones which will be changed into
Guard zones on the selected part sets. For example the
Control Panel is factory set with Zone 1 included. Thus the
Zone Type of Zone 1 will be changed (from Entry/Exit) into
Guard on Part Set 1.
From the Programming Menu, enter
are currently included will indicate.
Zon es
1 2 3 4 5 6 7 8
Press the appropriate numbered button(s) of the
zone(s) to be included or excluded. Press
system will chime to confirm that the new suite has been
accepted. The system will then automatically revert to the
Programming Menu.
INS034
$#
. The zones that
$#
U n set
T am per
. The
,
$$
. The zones that
$$
U n set
T am per
. The
,
$"
. The zones that
$"
U n set
T am per
. The
,

Programming the Date and Time

!"
It is ESSENTIAL to program the current date (
and time ( ) for correct operation of the service
$'
timer(s).
Programming the service timers (
) is prevented unless the current date (
$(
has first been programmed.
If the panel is completely powered down it will attempt
to store the current time and date in NVM and continue
from this point when it is powered up. However it may
be also desirable to select the Engineer Reset on
Power Up option (see page 18).

Programming the Date

From the Programming Menu, enter
look like this.
Zon es
1 2 3 4 5 6 7 8
Enter the current date as a 6 digit number; Day, Day,
Month, Month, Year, Year (e.g. to program the 1st of June
1998 enter
!#!'(*
each digit of the new date is entered. Press
system will chime to confirm the new date has been
accepted. The system will then automatically revert to the
Programming Menu and all the zone lights will illuminate.

Programming the Time

From the Programming Menu, enter
look like this.
Zon es
1 2 3 4 5 6 7 8
Enter the current time as a 6 digit number; Hour, Hour,
Minute, Minute, Second, Second using 24 hour format
(e.g. to program 7 minutes and 3 seconds past 2pm
(14:07:03) enter #%!)!"
as each digit of the new time is entered. Press
The system will chime to confirm the new time has been
accepted. The system will then automatically revert to the
Programming Menu.
Programming the Control Panel
$& - $'
,
$)
. The display will
$&
U n set
T am per
). The display will indicate as
,
$' . The display will
U n set
T am per
). The display will indicate
,
)
$&
,
$*
)
$&
$&
. The
$'
.
23