Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Texecom Veritas 8
Summary of Contents for Texecom Veritas 8
-
Page 1: Installation Manual
INSTALLATION MANUAL Security Control Panels INS034-9... -
Page 2: Table Of Contents
Table of Contents Table of Contents Section Page Programming Summary Programming Menu 1.1.1 Factory Settings Installation Introduction to the Control Panel Testing the Control Panel (Pre-Installation) Mounting the Control Panel Wiring the Control Panel 2.4.1 Veritas PCB Layouts 2.4.2 Wiring the External Sounder and Strobe 2.4.3 Magnetic Contacts and Panic Buttons 2.4.4... - Page 3 Table of Contents Table of Contents Section Page 3.11 Programming the Date and Time 3.11.1 Programming the Date #& 3.11.2 Programming the Time 3.12 Programming the Service Timers 3.12.1 Programming Service Timer One (Reminder) 3.12.2 Programming Service Timer Two (Nuisance) 3.12.3 Programming Service Timer Three (Lockout) 3.13...
-
Page 4: Programming Summary
Programming Summary 1 Programming Summary 1.1 Programming Menu Programming Option Programming Factory Option Code Procedure Setting " Miscellaneous Selections Zero Select/De-select Option Number(s) Press !" " Miscellaneous Selections One Select/De-select Option Number(s) Press " Miscellaneous Selections Two Select/De-select Option Number(s) Press "... -
Page 5: Factory Settings
Programming Summary Test Zone Extended Number Outputs Function Type Display !& "+ All Off Bell Set +Ve Bell & Global Tamper Strobe Alarm +Ve & Reset Inhibited Entry Power Sounder Lo Reset Guard Lid Tamper (inc. RKP) Sounder Hi Tamper Fire Mains Fail Tamper... -
Page 6: Installation
Installation 2 Installation 2.1 Introduction to the Control Panel The control panel is designed to maximise user friendliness for both the installer and the user. Programming is usually unnecessary as the factory settings (section 1.1.1, page 5) have been carefully selected to suit most installations without alteration. However all functions are fully programmable for Complete Control. -
Page 7: Wiring The Control Panel
1) Although the Veritas has been designed for maximum compatibility, for optimum performance, it is highly recommended that the Veritas should be used with Texecom's range of detectors, sounders and batteries. 2) The control panel is supplied with links fitted across the eight zones (Z1 -... -
Page 8: Veritas Pcb Layouts
Installation 2.4.1 Veritas PCB Layouts Figure 1 - Veritas PCB Layouts Figure 1a Veritas 8 PCB Figure 1b Veritas 8 Compact PCB Figure 1c Veritas R8 PCB INS 034-9... -
Page 9: Wiring The External Sounder And Strobe
Installation 2.4.1.1 PCB Terminals and Fuses Terminal Description Note AC (2) Transformer AC in NOT for mains supply BATT- Standby Battery negative BATT+ Standby Battery positive SAB Strobe switched negative SAB negative Supply SAB negative Tamper return SAB Bell switched negative SAB positive Supply L/S (2) Loudspeaker... - Page 10 The following diagrams illustrate how to connect the control panel to the most popular makes of SAB: Figure 3 - Common SAB Connections Figure 3a - Texecom Azura/Tempest Figure 3b - Texecom Odyssey Series Figure 3c - MAS Modular 3 INS 034-9...
- Page 11 Installation Figure 3d - Citadel Defender Figure 3e - Volumatic Flashguard Figure 3f – Gardiner Technology Novagard 2 Figure 3g - Activeguard AU101 Figure 3h - CQR Integra HS INS 034-9...
-
Page 12: Magnetic Contacts And Panic Buttons
Installation 2.4.3 Magnetic Contacts and Panic Buttons These are connected to one of the eight terminal pairs labelled Z1 to Z8 on the control panel. Figure 4 - Wiring Magnetic Contacts Figure 4a - Wiring a Single Magnetic Contact to a Zone (see also Figure 6) Figure 4b - Wiring Multiple Magnetic Contacts to a Zone (see also Figure 6) Mixing powered detectors and magnetic contacts on one zone is easiest if the wiring is taken from the control panel to the powered detectors first. -
Page 13: Powered Detectors
Installation 2.4.4 Powered Detectors Always consult the manufacturer's connection instructions. Powered detectors are connected to one of the eight terminal pairs labelled Z1 to Z8 on the control panel and are powered from the two terminals labelled AUX on the control panel as follows: Terminal Connect To Suggested Colour... -
Page 14: Extension Speaker(S)
Installation 2.4.5 Extension Speaker(s) These are connected to the two terminals on the control panel labelled L/S. 1) The total load including the built-in speaker must not be less than 4Ω (e.g. 2 x 8Ω speakers in parallel, 4 x 16Ω speakers in parallel, 2 x 2Ω speakers in series, 4 x 1Ω... -
Page 15: Commissioning The System (Initial Power Up)
Installation 2.5 Commissioning the System (Initial Power Up) ALWAYS Ensure the mains is off BEFORE removing the front cover ! Connect the black battery lead to the negative (-) terminal of the standby battery and the red battery lead to the positive (+) terminal of the standby battery. All the indicator lights will come on. -
Page 16: Servicing The System
Installation 2.6 Servicing the System ALWAYS Ensure the mains is off BEFORE removing the front cover 1) The Power light on the control panel is a status indicator for the battery charging circuit, a steady light meaning normal. A flashing light means action required - mains power can still be present. -
Page 17: Trouble Shooting
Installation 2.7 Trouble Shooting ALWAYS Ensure the mains is off BEFORE removing the front cover When replacing a fuse always observe the specified rating and type - failure to do so is dangerous and will invalidate the warranty. Fuses should comply with IEC 127. -
Page 18: Unit Will Not Set And Bleeps 9 Times
Installation 2.7.6 Unit Will Not Set and Bleeps 9 Times The system has a tamper fault and the Tamper light will be on. Using the extended display during Walk Test (section 3.5, page 25) identify the cause of the tamper fault: ! If the extended display identifies the fault as bell box tamper, then the cause may either be Bell Tamper or Global System Tamper. -
Page 19: System Operates But Remote Keypad Makes No Sound
Installation 2.7.10 System Operates but Remote Keypad Makes No Sound ! If an older version remote keypad has been fitted the system must be programmed for old style sounds as follows: Enter the Engineer code ++++ press , enter , press , press , press 2.7.11... -
Page 20: Programming
Programming 3 Programming Programming is usually unnecessary as the factory settings have been carefully selected to suit most installations without alteration. However all functions are fully programmable for Complete Control. 3.1 The Programming Menu The Programming Menu can only be accessed when the control panel is unset. . -
Page 21: Miscellaneous Selections One
Programming 1) Single Button Setting (Option 3) allows the system to be set using the keys without the need to first enter a User code. 2) EN50131-1 Requirements (Option 5) invokes the following features (see section 4.8.1, page 40): a) Reset (after an alarm) requires the use of a User code. b) An entry alarm (defined as an entry timeout or, a Guard zone activation during the entry period) invokes a 30 second delay during which the communicator output and external sounder are suppressed (i.e. -
Page 22: Miscellaneous Selections Two
Programming Disclaimer: It is the responsibility of the Installer to guard against losing locked Engineer codes. Texecom accept no liability whatsoever for any loss resulting from locked Engineer codes. 3.2.3 Miscellaneous Selections Two From the Programming Menu, enter . The zone lights of the options currently selected will illuminate. -
Page 23: Engineer Reset
When an Engineer Reset is required, the zone lights will display a random 4 digit sequence. Each digit will flash in turn and then pause before repeating. Texecom's Anti-Code software will accept this sequence to generate a 4 digit code which should be entered, after which the system can be reset as normal. -
Page 24: Push To Set
Programming 3.2.6 Push To Set Push to Set is intended to reduce false alarms due to user error when full setting the system. The user starts full set in the usual way and leaves the premises. However the system will ONLY set when an external push button is pressed. 1) The Zone Type of the zone to which the external push button is connected must be programmed as Push to Set (section 3.9, page 27): a) If this zone is set to chime (see User Guide) then the push button can... -
Page 25: Walk Testing
Programming 1) The zone light corresponding to each output will illuminate when it is on. 2) Several Texecom bell boxes feature a unique, patented "Engineer Hold-Off Mode" which disables Self-Activate on Lid Tamper to facilitate convenient servicing. Option will cause the strobe output to pulse 3 times to invoke Hold-Off Mode. -
Page 26: Re-Loading The Factory Settings
Programming 3.6 Re-Loading the Factory Settings From the Programming Menu, enter . All the zone lights will turn off. Press . The system will chime to confirm that all the factory settings have been re-loaded into the Non Volatile Memory. The system will then automatically revert to the Programming Menu and all the zone lights will illuminate. -
Page 27: Configuring The Remote Keypad(S)
Programming 1) If selecting one of the options which incorporate latching sensor reset (2, 3 or 6) the user can force a latching sensor reset, to clear the Latch/FTA indication, by entering their code and pressing 2) The SW+ output can only sink (not source) current. If powering detectors from the SW+ output, connect the detector +Ve to AUX+ and the detector -Ve to SW+. - Page 28 Programming Each zone may be programmed with one of these Zone Types which are described in the following sections: 3.9.1.1 Push To Set " Push to Set is intended to reduce false alarms due to user error when full setting the system.
-
Page 29: Programming The Zone Type
Programming 3.9.1.6 Entry/Exit Opening a zone with this Zone Type when the system is set will cause the control panel to start entry mode. This Zone Type would typically be used for a front door magnetic contact or, if one is not fitted, a hall PIR. The Final Door Set option (section 3.2.2, page 21) will cause the exit time to be reduced to 3 seconds when an Entry/Exit zone is closed during exit mode. -
Page 30: Changing Zone Types When Part Setting
Programming For example to program Zone 7 as a Guard zone, enter , press , press ") Description " Program Zone Type Zone = 7 Zone Type = Guard Program A zone is often referred to by its Zone Type, e.g. a zone with the PA Zone Type would be referred to as a PA zone. -
Page 31: Programming The Zones That Will Change To Entry/Exit
Programming Zone 1 will change (from Entry/Exit) into Guard and Zone 2 will change (from Inhibited Entry) into Entry/Exit. 24 Hour zones (Fire, PA and Tamper), Keyswitch zones and Push to Set zones should be monitored constantly and should NOT be programmed to change when the system is part set. -
Page 32: Programming The Date
Disclaimer: It is the responsibility of the Installer to obtain prior written agreement from the Customer regarding any use of a Service Timer. Texecom accept no liability whatsoever for any dispute resulting from the use of Service Timers. Service Timer One is designed to be used as a reminder. When it expires it turns on high level chime on all eight zones the first time the panel is set/unset. -
Page 33: Programming Service Timer One (Reminder) #)
Programming 3.12.1 Programming Service Timer One (Reminder) From the Programming Menu, enter . All the zone lights will turn off. Enter Service Timer One (Reminder) date as a 6 digit number; Day, Day, Month, Month, Year, Year (e.g. to program the 1st of April 1999 enter !"!%(( Zone lights 1, 2, 3, 4, 5 and 6 will illuminate in turn as each digit of the new date is entered. -
Page 34: The Seven Event Basic Log
Programming The system will automatically revert to the Programming Menu and all the zone lights will illuminate. 1) The Bell Cut Off Time is the length of time for which the bell sounds. & 2) The Part Set Error Tone Suspension Time would typically be used to suspend the error tone (indicating an open zone) to avoid disturbance when there are detectors on the part set exit route. -
Page 35: Programming The Suites
Programming 3.15 Programming the Suites The system has two Part Set Suites, a Chime Suite, a Double Knock Suite, a Manual Omit Suite, a Zone Disable Suite and a Zone Soak Test Suite all of which are programmable. 24 Hour zones (Fire, PA and Tamper), Keyswitch zones and Push to Set zones should be monitored constantly and should NOT be omitted by the Part Set Suites. -
Page 36: Programming The Manual Omit Suite
Programming 1) The Double Knock Suite defines the zones that will be assigned a double knock attribute. 2) A zone should be assigned a double knock attribute when maximum false alarm protection is required. A zone with a double knock attribute must be activated either twice within 10 seconds or once for longer than 10 seconds in order to cause an alarm. -
Page 37: Changing The Engineer Code
Programming The Zone Soak Test Suite defines the zones that are on Soak Test. To program the Zone Soak Test Suite, enter . The zone lights of the zones currently included in the Zone Soak Test Suite will illuminate. Press the appropriate numbered button(s) of the zone(s) to be included or excluded. -
Page 38: Technical Specification
4.2 Physical Rechargeable Battery Capacity Veritas 8 Compact: 1.2 to 2.1Ah see safety notes 3, 4 & 5 Veritas 8 & Veritas R8: 1.2 to 7.0Ah see safety notes 3, 4 & 5 Dimensions Veritas 8 Compact: 246mm x 185mm x 55mm Veritas 8 &... -
Page 39: Fuses
Technical Specification 4.5 Fuses A spare mains fuse is supplied in a clip adjacent to the mains terminal block. see safety note 7 Spare PCB fuses are supplied in a press-seal bag. see safety notes 7 & 8 Mains 230V T125mA, 250V, 20mm see safety note 7 Mains 115V... -
Page 40: European Standards
! EN 50131-1 requires that detector activation LEDs shall only be enabled during Walk Test. This is most conveniently achieved by using detectors with a Remote LED Disable input (e.g. the Texecom Rf360, Rf650 & RfExtreme PIRs) connected to the panel SW+ output, programmed to operate during Walk Test (section 3.7, page 26). -
Page 41: Warranty
(details on request). As the Veritas is not a complete alarm system but only a part thereof, Texecom cannot accept responsibility or liability for any damages whatsoever based on a claim that the Veritas failed to function correctly. -
Page 42: Installation Records
Installation Records 5 Installation Records 5.1 Installation Details Installation Engineer: Installation Company: Address: Telephone: Installation Date: High Area Zone Zone Type Loop Resistance Loop Resistance Protected (Clear) (Fault) The Instructions MUST NOT be Stored inside the Control Panel. 5.2 Maintenance & Call-Out Record Date/Time Reason for Site Work Carried... -
Page 43: Registered Installer Application Form
Fax back to 01706-213-187 or post to the address overleaf. Alternatively register online at http://www.texe.com Texecom make PIRs, Dual Technology Detectors, Shock Sensors, Internal & External Sounders, Control Panels, Cameras and Accessories. Ask your Distributor about our Award Winning range of Security Products. -
Page 44: Technical Support
• Free Product Voucher • Free Product Training • Latest Product Information Simply complete the form on the reverse of this page, and either fax or send it to Texecom to become a Registered Texecom Installer. Registration available to UK Professional Installers only.
Need help?
Do you have a question about the Veritas 8 and is the answer not in the manual?
Questions and answers