Cub Cadet Tank S S7232D Operator's Manual page 6

5. Brush Guards and canopies can afford additional
protection for the operator. The Brush Guard can deflect
tree limbs, clothes lines, and other obstacles that otherwise
could come in contact with the ROPS and OPDs. Contact
of ROPS and OPDs by items such as tree limbs, clothes
lines, guy wires, and buildings, could create hazardous
conditions whereby the machine could experience a tip-
over or roll-over. The canopy can provide protection for
the operator from some environmental exposure (sunlight,
rain, etc.). Work lights may be available.
6. The ROPS and seat belt are integral parts of this machine
and should not be tampered with, modified in any manner,
or removed.
7. The ROPS extends above and behind the operator position,
and therefore the operator must be aware of potential
contact of the ROPS with items such as trees, buildings,
doorways, clothes lines, utility wires, etc., that could cause
the machine to upset or rollover. Use caution in (or avoid)
areas where the ROPS could come in contact with any
structures, trees, etc.
8. The ROPS and seat belt add additional mass that elevates
the machine's Center of Gravity (C.G.) which negatively
affects the machine's stability and traction. Use extra
caution when operating on slopes.
9. Inspect the ROPS and seat belt assemblies on a regular
basis for damage and improper operation. Replace all
components that are damaged or are not functioning
properly with authorized replacement parts.
10. Fail ure to use the seat belt properly could result in serious
injury or death if an accidental overturn occurs. In order
for the ROPS to be effective, the seat belt must be securely
fastened around the operator at all times when the
operator is on the machine. Contact with the ROPS during
an overturn could cause serious injury or death.
11. The ROPS will not prevent the machine from upsets or roll
overs.
12. Only approved attachments should be used on this
machine.
Hydraulic Devices and Systems
Hydraulic fluid escaping under pressure may have sufficient force
to penetrate skin and to cause serious injury. If foreign fluid is
injected into the skin, it must be surgically removed within a few
hours by a doctor familiar with this form of injury, or gangrene
may result.
WARNING:
pinholes or nozzles that could eject hydraulic fluid
under high pressure. Use paper or cardboard, not
hands, to search for leaks!
Safely relieve all pressure in the system before performing any
work on the system, and make sure that:
• The ignition switch is OFF
• The key is removed
• The engine spark plug wire(s) removed
• All connections to the negative terminal of the battery are
removed
6 s 2 — i
ectiOn MpOrtant
Keep body and hands away from
s O p
afe peratiOn ractices
• The park brake is set
• All by-pass valves, if so equipped, are open
• Hydrau lic controls are actuated to release pressure on
pumps, cylinders, etc. If "float" positions are available, they
should be used.
After the above operations are completed, it should be safe to
begin disconnecting the lines or components. It is still a good
idea to cover the connection with a cloth shield and then gently
loosen connections.
WARNING:
Make sure all hydraulic fluid
connections are tight and all hydraulic hoses and
lines are in good condition before applying pressure
to the system.
Service
Related to Fuel
1. Fuel is highly flammable and its vapors can explode if
ignited. Please respect it.
2. Do not smoke or permit others to smoke while handling
fuel.
3. Always use approved containers for fuel and fill slowly
to decrease the chance of static electricity buildup and
spillage.
4. Store fuel in well ventilated and unoccupied buildings
away from sparks and flames.
5. When dispensing fuel into approved containers, place the
container on the ground when refueling to avoid a possibel
static electricity ignition of fuel vapors.
6. Do not fill containers while it is inside a vehicle, trunk, bed
of a pickup or floor of the trailer.
7. Always shut off the engine and permit it to cool before
removing the fuel tank cap.
8. Always fill the fuel tank outdoors.
9. If the fuel container spout will not fit inside the fuel tank
opening, use a funnel.
10. When filling the fuel tank, stop when the fuel reaches
one inch from the top. The space is necessary for tank
expansion. DO nOT OVERFILL.
11. Wipe up any spilled fuel.
General Service
1. Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless,
and deadly gas.
2. Before cleaning, repairing, or inspecting, make certain the
blade(s) and all moving parts have stopped. Disconnect the
spark plug wires and remove the key from the ignition to
prevent unintended starting.
3. Periodically check to make sure the blades come to
complete stop within approximately (5) five seconds after
operating the blade disengagement control. If the blades
do not stop within the this time frame, your machine
should be serviced.