JVC BD-X200E Instructions Manual page 62

Synchronous Recording
Recording Playback Signals From a VCR with RS-422A (continued)
Editing Via the REMOTE CONTROL (9PIN MASTER/DV MASTER) Screen
A keyboard and mouse can be used as an alternative to the DVD recorder's buttons when using the REMOTE CONTROL (9PIN
MASTER/DV MASTER) screen.
Front panel : Select using the cursor buttons (t, 8, 7, and 6), and confirm the selection using the SET button.
: Select using the arrow keys (†, ©, √, and ∞), and confirm the selection using the Enter key.
Keyboard
Mouse : Left click the required button.
* When the REMOTE CONTROL screen is being displayed, the DVD recorder's, FWD, REV, PLAY, REC, PAUSE, MENU, and TOP
MENU buttons will be disabled.
In Point (start point for editing):
Set the time code (hours : minutes : seconds : frames) of
the position on the playback tape where recording is to
be started.
Chapter list:
This displays the time
codes of chapter
marks.
The In Point's time
code is registered as
the first chapter
mark.
A total of 98 chapters
can be setup.
When CHAPTER
CREATION from the
RECORDER MENU
(2/2) screen is set to
MANUAL, it will be
possible to setup
chapter marks at any
position on the
playback tape.
CHAPTER:
The right-hand field indicates
the current setting for
CHAPTER CREATION from
the RECORDER MENU (2/2)
screen.
When set to MANUAL,
chapter marks can be
registered in this screen's
chapter list.
When set to AUTO, the
DVD recorder's chapter
auto-create function will set
chapters. In such a case, it
will not be possible to
register chapters using this
screen's chapter list.
Chapter marks
inserted at GOP intervals
(i.e., 15 frames). It will not
be possible to inser t
chapter marks that are
closer together than this
interval.
E-60
REMOTE CONTROL SCREEN ( 9PIN MASTER )
EXIT IN POINT
: : :
h m s
f
1 00:00:00:00
4
00:25:00:00
7 00:40:00:00
CHAPTER
ADJ
BITRATE
TC SET
TC CANCEL
ADJUST:
This button can be
pressed to determine
the remaining disc time
based on the editing
time and to also set a
suitable bit rate. This
setting is
displayed in the BIT
RATE field.
VCR Control Panel
The buttons provided in this panel are used to control VCR operations. When a
button is selected and confirmed, the VCR will carry out the corresponding operation.
It is important to remember that these buttons do not control operation of this DVD
recorder.
are
e : Eject
u : Fast reverse or fast-reverse play
: Frame-Reverse play
q
: Stop
* The action to be taken by the DVD recorder in response to pressing of the y or
u button (i.e., FF/REW or SEARCH) is selected using REM FF/REW MODE
from the REMOTE MENU screen.
Out Point (end point for editing):
Set the time code (hours : minutes : seconds : frames) of
the position on the playback tape where recording is to
be stopped.
00:00:00:00
OUT POINT
: : :
h m s
f
2 00:15:00:00 3 00:20:00:00
5 6
00:30:00:00 00:35:00:00
8 00:45:00:00 9 00:50:00:00
TC INPUT
MANUAL
8.0 Mbps DISC REMAIN
EDL LOAD
EDIT/END
TC SET
TC CANCEL : This button is used to remove setting values
EDL LOAD
then EDIT/END
w : Pause
t : Play
y : Fast forward or fast-forward play
TC INPUT:
This field is used to input
time codes for the In
00:10:00:00
Point, Out Point, and
chapter marks from the
: : :
h m s
f
keyboard.
DISC REMAIN:
: : :
This field shows an
estimate of the remaining
000 min
space for recording on the
FINALIZE
disc.
FINALIZE:
This button is used to
finalize the disc.
: This button is used to set input time codes for
the In Point, Out Point, and chapter marks.
for the In Point, Out Point, and chapter marks.
: This button is used to load the most-recent
edit list. It can be used whenever CREATION
CHAPTER has been set to MANUAL.
: This button is used to start editing
automatically. When recording has ended, the
DVD recorder automatically adopts Recording
STOP mode. If selected while editing, this
button will end that process.
: Frame-advance play