Panasonic AG-6124 Service Manual page 6

@ AEMOTE contro! connector
For connecting the AG-A11 remote controller which
is available as an optional accessory.
@ MIC input jack
input jack (3 mm) for an external microphone.
This jack has precedence when signals are supplied
simultaneously to this jack and the audio input con-
nectors.
@ (INT TIMER display tamp
This lights when internal timer recording has been
set.
@ TIMER MODE (REC MODE) button
This is the operation button for internal timer re-
cording or external timer recording. The displays
shown below light on the display panel.
INT: At the times set by the internal timer, the power
is automatically tumed on or off and recording
Starts or stops.
No display: When timer recording is not performed.
EXT: When the external power is turned on, record-
ing starts automatically.
@ Display pane!
intemal timer
recording mode
. Memory stop
Recording ond d i mode display
Tape counter mode display
« Operation mode displays
Le Operon inode = Deo)
Fiayback | » if
Recording ® REC lamp fights.
Stilt picture i \
Recording pause
§8 REC lamp lights. |
Recording check & REC lamp lights.
Fast forwarding
Rewinding
Cue
Review
Forward field advance
Reverse field advance
« Error messages
An error code appears when trouble has occurred
during operation.
E-2: Trouble in video cassette insertion area
E-3: Trouble in video cassette tape loading area
E-4: Trouble in cylinder area
£-5: Trouble in tape transport area
d: Formation of condensation (dew)
@ ALARM display lamp
This remains lighted while alarm recording is in pro-
gress. It flashes when alarm recording ends.
@® SUMMER TIME button
This is used to switch between the present time
and summer (daylight saving) time.
© TIME MODE button
This is used to select the recording and playback
time mode. Each time this is pressed, the time mode
changes in the following sequence:
ee eee
STOP (shift) button
When this is pressed, the tape stops traveling. When
it is pressed while a menu screen is displayed, the
setting items move downward.
@ PAUSE/STILL (shift) button
When this is pressed during recording, the tape tem-
porarily stops traveling. When pressed during
playback, the tape temporarily stops traveling, and
a still picture appears on the TV monitor. When
pressed again, the tape travel resumes.
When it is pressed while a menu screen is displayed,
the setting items move toward the right.
@ Field REV ADV (set) button
When this is kept depressed during still-picture play-
back, the picture is advanced field by field in the
reverse direction. When it is released, the still picture
reappears. When a menu screen is displayed, it is
used to change an item (decrement a value).
@ Field FWD ADV (set) button
When this is kept depressed during still-picture play-
back, the picture is advanced field by field in the
forward direction. When it is released, the still picture
reappears. When a menu screen is displayed, it is
used to change an item (increment a value).
® FF button
When this is pressed, the tape is fast forwarded.
When it is kept depressed during playback, the unit
is placed in the cue mode.
OPERATING INSTRUCTIONS a
@ Audio input/output connectors
Audio input/output connectors (phono jacks)
@ Vertical hold controis (3h, 6h)
When the image on the TV monitor runs vertically
during still-picture playback, adjust these controls
by turning them with a small screwdriver.
© Video input/output connectors
Video input/output connectors (BNC); connect the
input connector to the video camera, etc. and the
output connector to the TV monitor, etc.
© Camera switching output connector
Camera switching output connector; connect it to
the sequential switcher.
© Battery installation area
Install the battery in this area. See "Lithium Battery"
on page 3.
© Alarm input connector
Alarm recording input connector; connect it to the
external sensor.
7
£8)
£9
Ground terminal
Alarm reset connector
Input connector for releasing alarm recording; a +4
to +14V DC voltage is required.
SUMMER TIME connector
This is used to switch between the present time
and summer time. (See page 14.)
Tape end output connector
When the cassette tape comes to its end during
recording, the alarm device installed extemally is
activated.
Auto off output connector
When trouble has occurred in the unit, the alarm
device installed externally is activated.
Ground terminal
Power cable