Warnings And Faults - ABB ACQ580-01 Quick Installation And Start-Up Manual

Warnings and faults

Warning Fault Aux. code
A2A1 2281 Current calibration
A2B1 2310 Overcurrent
A2B3 2330 Earth leakage
A2B4 2340 Short circuit
- 3130 Input phase loss
- 3181 Wiring or earth fault
A3A1 3210 DC link overvoltage
A3A2 3220 DC link undervoltage
- 3381 Output phase loss
- 5090 STO hardware failure
A5A0 5091 Safe torque off
A7CE 6681 EFB comm loss
A7C1 7510 FBA A communication
A7AB - Extension I/O
configuration failure
AFF6 - Identification run
- FA81 Safe torque off 1
- FA82 Safe torque off 2
Ratings, fuses and typical power cable sizes
ACQ580- Nominal ratings
01-...
Input Output
current current
light duty
I I
1 LD
A A
U = 200...240 V, P at U = 3-phase 208/230 V, 60 Hz
1 n n
04A6-2 4.6 4.6
06A6-2 6.6 6.6
07A5-2 7.5 7.5
10A6-2 10.6 10.6
017A-2 16.7 16.7
024A-2 24.2 24.2
031A-2 30.8 30.8
046A-2 46.2 46.2
059A-2 59.4 59.4
U = 440...480 V, P at U
= 3-phase 460 V, 60 Hz
1 n n
02A1-4 2.1 2.1
03A0-4 3.0 3.0
03A5-4 3.5 3.5
04A8-4 4.8 4.8
06A0-4 6.0 6.0
07A6-4 7.6 7.6
012A-4 12.0 12.0
014A-4 14.0 14.0
023A-4 23.0 23.0
027A-4 27.0 27.0
034A-4 34.0 34.0
044A-4 44.0 44.0
U = 500...600 V, P at U
= 3-phase 575 V, 60 Hz
1 n n
Description
Warning: Current calibration is done at the next start.
Fault: Output phase current measurement fault.
The output current is more than the internal limit. This can also be caused by
an earth fault or phase loss.
A load unbalance that is typically caused by an earth fault in the motor or the
motor cable.
There is a short-circuit in the motor or the motor cable.
The intermediate DC circuit voltage oscillates due to missing input power
line phase.
Incorrect input and motor cable connection.
Intermediate DC circuit voltage is too high.
Intermediate DC circuit voltage is too low.
All three phases are not connected to the motor.
STO hardware diagnostics has detected hardware failure. Contact ABB.
The Safe torque off (STO) function is active.
Break in embedded fieldbus communication.
Communication lost between drive (or PLC) and fieldbus adapter.
The installed C-type module is not the same as configured, or there is an
error in the communication between the drive and module.
The motor ID run occurs at the next start.
The Safe torque off circuit 1 is broken.
The Safe torque off circuit 2 is broken.
4)
Fuses
Motor gG fuse
1) 2)
power
(IEC 60269)
P P
ABB type
n LD
kW hp
0.75 1.0 OFAF000H25
1.1 1.5 OFAF000H25
1.5 2.0 OFAF000H25
3.0 3.0 OFAF000H25
4.0 5.0 OFAF000H25
5.5 7.5 OFAF000H40
7.5 10.0 OFAF000H40
11.0 15.0 OFAF000H63
15 20 OFAF000H63
0.75 1.0 OFAF000H4
1.1 1.5 OFAF000H6
1.5 2.0 OFAF000H6
2.2 3.0 OFAF000H10
3.0 3.0 OFAF000H10
4.0 5.0 OFAF000H16
5.5 7.5 OFAF000H16
7.5 10.0 OFAF000H25
11.0 15.0 OFAF000H32
15.0 20.0 OFAF000H40
18.5 25.0 OFAF000H50
22.0 30.0 OFAF000H63
Typical power cable sizes,
Cu
uR/aR UL class
3)5) 6)7)8)
fuse T
(DIN 43620)
Bussmann type
mm
170M1563 JJS-15 3×1.5 + 1.5
170M1563 JJS-15 3×1.5 + 1.5
170M1563 JJS-15 3×1.5 + 1.5
170M1563 JJS-15 3×1.5 + 1.5
170M1563 JJS-30 3×2.5 + 2.5
170M1565 JJS-40 3×4.0 + 4.0
170M1565 JJS-40 3×6.0 + 6.0
170M1566 JJS-80 3×10 + 10
170M1566 JJS-80 3×10 + 10
170M1561 JJS-15 3×1.5 + 1.5
170M1561 JJS-15 3×1.5 + 1.5
170M1561 JJS-15 3×1.5 + 1.5
170M1561 JJS-15 3×1.5 + 1.5
170M1561 JJS-15 3×1.5 + 1.5
170M1561 JJS-15 3×2.5 + 2.5
170M1561 JJS-15 3×2.5 + 2.5
170M1563 JJS-30 3×2.5 + 2.5
170M1563 JJS-30 3×6 + 6
170M1565 JJS-40 3×10 + 10
170M1565 JJS-60 3×10 + 10
170M1566 JJS-60 3×10 + 10
Frame
size
2 9) 10)
AWG
14 R1
14 R1
14 R1
14 R1
10 R1
8 R2
8 R2
6 R3
4 R3
14 R1
14 R1
14 R1
14 R1
14 R1
14 R1
14 R1
12 R2
10 R2
8 R3
8 R3
6 R3
11