Maintenance; Three-Year Limited Warranty - DeWalt DCCS620B Instruction Manual

0.025" (0.635 mm) below the tips of the cutters as shown
in Fig. V.
5. Fig. W- Keep all cutter lengths equal.
6. If damage is present on the chrome surface of the top
plates or side plates, file back until such damage is removed.

CAUTION: After filing, the cutter will be sharp, use extra
caution during this process.
nOTE: Each time the chain is sharpened, it loses some of
the low kickback qualities and extra caution should be used.
It is recommended that a chain be sharpened no more than
four times.
Fig. U
21
Fig. V
Fig. W
Accessories

WARNING: Since accessories, other than those offered by
D WALT, have not been tested with this product, use of such
e
accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT recommended accessories should
e
be used with this product.
Recommended accessories for use with your tool
are available at extra cost from your local dealer or
authorized service center. If you need assistance in
locating any accessory, please contact D
Tool Co., 701 East Joppa Road, Towson, MD 21286, call
1-800-4-D WALT (1-800-433-9258) or visit our website:
e
www.dewalt.com.

WARNING: The use of accessories not recommended in
this manual may be hazardous.
Replacement chain and bar are available from your nearest
D WALT authorized service center. For use only with low
e
kick back bar and chain.
Available bars and chains for DCCs620:
Bar: service part number N594322
Chain: service part number N580237

MAINTENANCE


injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can
cause injury.
Cleaning

clean, dry air at least once a week. To minimize the risk of eye
injury, always wear ANSI Z87.1 approved eye protection when
performing this.

for cleaning the non-metallic parts of the tool. These
chemicals may weaken the plastic materials used in these
parts. Use a cloth dampened only with water and mild soap.
60°
Never let any liquid get inside the tool; never immerse any part
of the tool into a liquid.
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.

0.025" repairs, maintenance and adjustment (including brush
(0.635 mm) inspection and replacement, when applicable) should be
performed by a factory service center or an authorized service
center. Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will help
you obtain more efficient warranty service in case there is a
problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of an
insurance loss, such as fire, flood or theft, your registration of
ownership will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification is
required under the Federal Consumer Safety Act.
• Register online at www.dewalt.com.
Three‑Year Limited Warranty
For warranty terms, go to https://www.dewalt.com/
support/warranty.
To request a written copy of the warranty terms, contact:
Customer Service at D
Joppa Road, Towson, MD 21286 or call 1‑800‑4‑D
(1‑800‑433‑9258).
WALT Industrial
e
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country-specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
FREE WARning lABEl REPlACEMEnT: If your warning
labels become illegible or are missing, call 1‑800‑4‑D
(1‑800‑433‑9258) for a free replacement.
WARNING: To reduce the risk of serious personal
WARNING: Blow dirt and dust out of all air vents with
WARNING: Never use solvents or other harsh chemicals
WARNING: To assure product SAFETY and RELIABILITY,
WALT Industrial Tool Co., 701 East
e
English
WALT
e
WALT
e
11