Table of Contents
Advertisement
Definitions: Safety Alert Symbols and Words
This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk
of personal injury or property damage.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
(Used without word) Indicates a safety related message.
NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.
Fig. A
2
12
1
Variable speed trigger
1
switch
Lock-off lever
2
Chain brake / front hand
3
guard
Guide bar
4
Saw chain
5
Sprocket cover
6
Battery Pack
7
Bar adjust locking knob
8
15
14
7
9
6
8
11
Chain tensioning knob
9
Oil level indicator
10
Guide bar scabbard
11
Rear handle
12
Front handle
13
Battery housing
14
Battery release button
15
Oil cap (not shown)
16
13
3
10
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
WARNING: To reduce the risk of injury, read the
instruction manual.
if you have any questions or comments about this or
any D
WALT tool, call us toll free at:
e
1-800-4-D
WALT (1-800-433-9258).
e
English
5
4
1
Advertisement
Table of Contents
Related Manuals for DeWalt DCCS670
Summary of Contents for DeWalt DCCS670
- Page 1 English Definitions: Safety Alert Symbols and Words This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
-
Page 2: General Power Tool Safety
English GENERAL POWER TOOL SAFETY b ) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust WARNINGS mask, non-skid safety shoes, hard hat, or hearing WARNING! Read all safety warnings and all protection used for appropriate conditions will reduce instructions. -
Page 3: Chainsaw Safety Warnings
English into account the working conditions and the surface. Slippery or unstable surfaces such as ladders may work to be performed. Use of the power tool for cause a loss of balance or control of the chain saw. operations different from those intended could result •... -
Page 4: Kickback Safety Features
English • Only use replacement bars and chains specified manual to help avoid kickback and other forces which by the manufacturer. Incorrect replacement bars and can result in serious injury. chains may cause chain breakage and/or kickback. • Reduced-Kickback Guide Bar, designed with a small radius •... -
Page 5: Chainsaw Names And Terms
English wash exposed areas with soap and water. Allowing • Replacement Saw Chain - A chain that complies with dust to get into your mouth, eyes, or lay on the skin may kickback performance requirements of ANSI B175.1–2000 promote absorption of harmful chemicals. when tested with specific chain saws. -
Page 6: Batteries And Chargers
English materials are created when lithium ion battery packs .....safety alert symbol .... Tip contact can cause are burned....Visible radiation the guide bar to move • If battery contents come into contact with the skin, suddenly upward and ..... Wear respiratory immediately wash area with mild soap and water. - Page 7 WALT (1-800-433-9258) or the gauge number of the wire, the greater the capacity visit our website www.dewalt.com. of the cable, that is, 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage The RBRC®...
-
Page 8: Charger Operation
English battery pack in the cavity. Unplug the charger before Minimum gauge for Cord sets attempting to clean. Total length of Cord in Feet Volts (meters) Charging a Battery (Fig. A) 120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7) 1. -
Page 9: Electronic Protection System
INTENDED USE the battery pack is charged when the air temperature is Your D WALT DCCS670 Chainsaw is ideal for pruning between 65 °F and 75 °F (18 ° – 24 °C). DO NOT charge applications and cutting logs up to 14" (355 mm) the battery pack in an air temperature below +40 °F... - Page 10 English • Flip up locking lever and rotate the bar adjust locking Fig. F knob 8 counterclockwise as shown in Figure D to remove sprocket cover 6 • Wearing protective gloves, grasp the saw chain 5 wrap it around the guide bar , ensuring the teeth are 4 ...
-
Page 11: Filling The Oil Reservoir
D WALT service center. WARNING: To reduce the risk of serious personal • DCCS670 requires replacement chain # DWRC1600, injury, turn unit off and remove the battery pack service part number 90618541. Replacement 16” bar, before making any adjustments or removing/ service part number 90618542. -
Page 12: On/Off Switch
English Fig. K • Do not hold chain saw by front hand guard/ chain brake 3 . Keep elbow of left arm locked so that left arm is straight to withstand a kickback. WARNING: Never use a cross-handed grip (left hand on the rear handle and right hand on the front handle). -
Page 13: Testing The Chain Brake
English • Pull the chain brake / front hand guard 3 towards the • Before felling is started, consider the natural lean of front handle 13 into the “set” position as shown in the tree, the location of larger branches and the wind Figure O. -
Page 14: Care And Maintenance
English Fig. R Fig. U 2nd CUT OVERBUCK (2/3DIAMETER) TO MEET 1st CUT (TO AVOID PINCHING) 1st CUT UNDERBUCK (1/3 DIAMETER) AVOID SPLINTERING Figure V- When supported at both ends. • Bucking First, cut 1/3 down from the top overbuck. Then make WARNING: Recommend that first time users should the finished cut by underbucking the lower 2/3 to meet practice cutting on a saw horse. -
Page 15: Maintenance
WALT authorized service center. For use only with low 2. Place the file holder flat on the top plate and depth kick back bar and chain. gauge of the cutter. Available bars and chains for DCCs670: 3. Figure W- Keep the correct top plate filing angle 19 ... -
Page 16: Register Online
DEWAlT BATTERY PACKs Product warranty voided if the battery pack is tampered with in any way. DeWalt is not responsible for any injury caused by tampering andmay prosecute warranty fraud to the fullest extent permitted by law. 90 DAY MOnEY BACK gUARAnTEE...