DIGITNOW M125 - Portable Digital Image Scanner Manual

Features

• Portable, high-resolution scanner for negative filmes and slide films
• High brilliance of colour (white balance & exposure compensation are automatically)
• 5 megapixle CMOS sensor
• 2.4" TFT display
• SD / SDHC card slot up to 32GB
• USB 2.0 interface (high speed)
• Usable as stand alone device
• Connect directly to the computer and read the photos saved on the SD card(Support for Windows and MAC)
• Small, light-weight, handy and easy to use

Package contents

• Film scanner
• USB cable
• Video cable
• Negative Film holder
• Positive slide holder
• Rapid slide feeder
• DC 5V adapter
• User's Manual
• Brush

Note: Place the film scanner on the side and insert the end of the brush into the door on the right side and clean the backlight panel placed in the film scanner.

Using the included Holders

With the lever all the way to the right, stack your slides in the rapid slide feeder.

• Place the rapid slide feeder into the FILM HOLDER SLOT.
• Push the lever towards the left, then pull the lever back to the right again to load a slide from the feeder into SLIDES 2. Repeat this step for subsequent slides (which will push the used slides out the other side).
  

Loading Slides

Hold up the slide toward the light. Face the trademark slide of the slide away from you. Look through the slide and it should appear normally (not a mirror image). Now turn the slide so the image is upside down while looking at the same side.

Open the slide holder at the marked spot on the top. With the slide holder laid open place the slide into recessed area in the holder, the slide should fit perfectly.

Close the slide holder and press the edges so that it locks in place. Hold it in the position as showing and insert the Slide Holder into the slot on the right side of the scanner.

Note: Handle slides and negatives with care. Dust, scratches or finger prints will show up on your saved images.

Loading Negatives

Hold up the negative toward the light. As you look through the negative, you should be able to read the small negative numbers normally (not a mirror image). Now turn the negative so the image is upside down while looking at the same side.

Open the negative holder at the marked spot on the top. With the negative holder laid open place the negative into holder so the notches line up with the notches on the holder.

Close the negative holder and press the edges so that it locks in place. Hold it in the position as shown in the film scanner. Insert the negative holder into the slot on the right side of the film scanner as shown.

Proper Operation Sequence

1. Slide or load film/negative film to board holder.
2. Insert board holder to scanner.
3. Connect scanner USB cable to PC.
4. Press power button to turn on scanner.
5. Press scanning button to start scanning.
6. Operation according to indication of manual on screen.
7. After finishing working, take storage card out.
8. Picture also can be read from PC through USB connection

1. Playback
2. Mirror Image/Rotation
3. Up
4. Down
5. Power on/off/ menu
6. Capture/ok

Power on/off

Power on:
Connect the product to power outlet via USB power adapter and USB cable or to PC via USB cable. Then Insert the SD card inside the product, short press ""MENU key. When "Power" indicator lights up and the "SD" indicator lights up, it processes into Capture mode.

Power off:
Long press "" MENU key for around 3 seconds, the "Power" indicator will light off, and the product will power off.

Capture Picture

1. After processing above instructions, connect the product to Power outlet via USB power adapter & USB cable or to PC via USB cable. Then Insert the SD card inside the product, short press "" MENU key. When "Power" indicator lights up and the "SD" indicator lights up, it processes into Capture mode.

2. Press "" MENU key, select positive film/ negative film / B & W film according to film types you have put into the film holders.
3. According to display on the screen, press " "key to mirror image to adjust the angle of films; Press""/ "" key to adjust the brightness of films.
4. press " " key and wait for 2 seconds, the images will automatically save into the SD card.
5. Press"" key to enter into playback mode, press""key again to exit the playback mode. (Note:"5M(10M)" on the top left corner of the screen indicates Resolution, the number at the top right corner indicates that how many images can the SD card save.)

Mirror Image/Rotation

If you need mirror image or rotation image when picture be scanning, you can press Rotation key to adjust it, then capture picture.

Press key (mirror image), the image place be altered (from left to right)

Continue Press key (rotation), the image place be altered (from up to down)

Main Menu

Enter / Exit Menu Mode

1. At Capture mode, press "" MENU key to enter into MENU.

2. At MENU mode, press"" MENU key or "" key to back to Capture mode; At MENU mode, press "" key to enter Playback mode.

Menu introduction

1. Capture mode: A: B&W film B: Positive film C: Negative film
2. Exposure: Exposure Compensation(EV -2~2)
3. Resolution: 5mega /10mega
4. Language : English, French, Deutsch, ltalian, Spanish, Chinese, Simplified Chinese, Japanese.
5. USB MSDC: MSDC mode (connect to PC)

Capture Option

Press ""MENU key to enter into MENU, press""/ "" to choose capture option, press "" key to enter into slide style. Choose needed image type like positive film, negative Film, B&W. (Please see following picture)

After enter into Slide style, according to film types which you have put in the film holders, press""/ ""to select the corresponding film mode and press "" to confirm it.

1. B&W film: choose B&W if there is B&W film at board holder
2. Positive film: choose positive film if there is positive film at board holder
3. Negative film: choose negative film if there is negative film at Board holder

Exposure

Press ""MENU key to enter into MENU, press ""/ "" key to choose Exposure option, and press "" key to enter into Exposure Compensation , then press""/ "" key to setting exposure value of scanning image, and press "" to save your setting.

Resolution

Press ""MENU key to enter into MENU, press""/ "" key to choose Resolution option and press "" to enter setting, then press""/ "" key to choose 5M or 10M resolution, and press "" to save the setting.

Language

Press ""MENU key to enter into MENU, press ""/ "" key to choose Language option and press "" to enter setting, then press""/ "" key to choose language, and press "" to save the setting.

Note: Choosing English, French, Deutsch, ltalian, Spanish, Chinese, Simplified Chinese, Japanese. according to user's need

USB MSDC

Press ""MENU key to enter into MENU, press ""/ "" key to choose USB MSDC option and press "" to enter USB MSDC. after the product successfully connect to PC via USB cable, the screen will light off, and the "PC" indicator will light up. Then you can preview images on PC and transfer images from the product to PC.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download DIGITNOW M125 - Portable Digital Image Scanner Manual