Advertisement
Quick Links
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
© 2020—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
CV
Debris Kit
STX-38 EFI Stump Grinder with Intelli-Sweep
Model No. 140-3624
Description
No parts required
Muffler guard
Bolt (5/16 x 2-1/2 inches)
Locknut (5/16 inch)
Top bracket
Bottom bracket
Left bracket
Hook and loop fasteners (from cylinder
cover)
Hook and loop fasteners (from hose
cover)
Cylinder cover
Hose cover
Bolt (1/4 x 1 inch)
Nut (1/4 inch)
Hydraulic cover
Guard mount
Clamp plate
Bolt (5/16 x 1-1/4 inches)
Locknut (5/16 inch)
Register at www.Toro.com.
Form No. 3436-227 Rev B
®
Installation Instructions
Qty.
–
Prepare the machine.
1
2
Replace the muffler guard.
2
1
1
1
Drill the bracket holes.
4
4
1
1
5
Install the covers.
5
1
1
2
Replace the guard mount.
2
2
All Rights Reserved *3436-227* B
Original Instructions (EN)
Printed in the USA
Use
Advertisement
Related Manuals for Toro 140-3624
Summary of Contents for Toro 140-3624
- Page 1 Form No. 3436-227 Rev B Debris Kit STX-38 EFI Stump Grinder with Intelli-Sweep ® Model No. 140-3624 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine.
-
Page 2: Preparing The Machine
Preparing the Machine No Parts Required Procedure Park the machine on a level surface. Engage the parking brake. Raise the grinder and support it using jackstands. Shut off the engine and remove the key. g309583 Figure 1 Allow the engine to cool completely. 1. - Page 3 Drilling the Bracket Holes Parts needed for this procedure: Top bracket Bottom bracket Left bracket Hook and loop fasteners (from cylinder cover) Hook and loop fasteners (from hose cover) g323226 Figure 4 Hose cover Procedure 1. 15.6 cm (6-1/8 inches) 3.
- Page 4 Note: Place the left bracket at the bottom of the welds Do not install the 15.6 cm (6-1/8 inch) of the wrap rod. Using the bracket as a template, fastener strip from the hose cover at this time. mark and drill holes (1/4 inch diameter) into the frame (Figure g323307...
-
Page 5: Installing The Covers
Installing the Covers Parts needed for this procedure: Cylinder cover Hose cover g322789 Bolt (1/4 x 1 inch) Figure 11 Cylinder cover attached to frame fastener strips Nut (1/4 inch) Hydraulic cover Wrap the longer lengths of the cover between Procedure the hydraulic cylinder and grinder pivot and adhere them together... - Page 6 Secure the bottom of the cover using the bottom Clean the surface of the hydraulic cover where bracket, 2 bolts (3/8 inch x 1-1/4 inch), and 2 you are adhering the fastener strip (Figure 14). nuts (1/4 inch) as shown in Figure Remove the backing from the remaining hook and loop fastener strip and adhere it on the...
- Page 7 Replacing the Guard Mount Parts needed for this procedure: Guard mount Clamp plate Bolt (5/16 x 1-1/4 inches) Locknut (5/16 inch) Procedure g309640 Figure 16 Remove the shield assembly from the grinder 1. Bolt—5/16 x 1-1/4 inches 4. Locknut—5/16 inch (12) head (Figure 15).
- Page 8 g309637 Figure 18 1. Bolt—5/16 x 1-1/4 inches 4. Guard mount (12) 2. Clamp plate (2) 5. Locknut—5/16 inch (12) 3. Shield (2) Using the clamp plate and guard mount as a template, drill a hole (5/16 inch diameter) into both shields (Figure 19).