Adjusting The Mirrors; Aiming The Headlights; Starting And Stopping The Engine - Toro Groundsmaster 4010-D Operator's Manual

cutting edge on inside edge of side cutting unit to
corresponding outside edge of front cutting unit and
compare. The side cutting unit measurement should be
within 3 mm (1/8 inch) of the front cutting unit.
Note: All three cutting units castor wheels should
remain on the ground with counterbalance applied.
Note: If adjustments need to be made to match the
cut between the front and side cutting units, make the
adjustments to the side cutting units only.
3. If the inside edge of the side cutting unit is too high
relative to the outside edge of the front cutting unit,
remove one 3 mm (1/8 inch) shim from the bottom
of the front inside castor arm on the side cutting unit
(Figure 30). Recheck measurement between outside
edges of both side cutting units and inside edge of side
cutting unit to outside edge of front cutting unit.
4. If inside edge is still too high, remove an additional
3 mm (1/8 inch) shim from bottom of front inside
castor arm of the side cutting unit and one 3 mm (1/8
inch) shim from the front outside castor arm of the
side cutting unit.
5. If the inside edge of the side cutting unit is too low
relative to the outside edge of the front cutting unit,
add one 3 mm (1/8 inch) shim to the bottom of the
front inside castor arm on the side cutting unit. Check
measurement between outside edges of both side
cutting units and inside edge of side cutting unit to
outside edge of front cutting unit.
6. If inside edge is still too low, add an additional 3 mm
(1/8 inch) shim to the bottom of front inside castor
arm of the side cutting unit and add one 3 mm (1/8
inch) shim to the front outside castor arm of the side
cutting unit.
7. Once cutting height matches at the edges of front and
side cutting units, verify that side cutting unit pitch
is still 8 to 11 mm (5/16 to 7/16 inch). Adjust as
necessary.

Adjusting the Mirrors

Cab model only
Rear View Mirror
While sitting in the seat, adjust the rear view mirror
31) to attain the best view out the rear window. Pull the lever
rearward to tilt the mirror to reduce the brightness and glare
of light.
Side View Mirrors
While sitting in the seat, have a helper adjust the side view
mirrors (Figure 31) to attain the best view around the side of
the machine.
1. Side view mirrors
2. Rear view mirror

Aiming the Headlights

1. Loosen the mounting nuts and position each headlight
so that it points straight ahead. Tighten the mounting
nut just enough to hold the headlight in position.
2. Place a flat piece of sheet metal over the face of the
headlight.
3. Mount a magnetic protractor onto the plate. While
holding the assembly in place, carefully tilt the headlight
downward 3 degrees, then tighten the nut.
4. Repeat the procedure on the other headlight.
Starting and Stopping the
Engine
Important: The fuel system will automatically bleed
itself when any of the following situations occur:
•
Initial start up of a new machine.
•
The engine has ceased running due to lack of fuel.
•
Maintenance has been performed upon the fuel system
components.
1. Ensure that the parking brake is set. Remove your foot
from the traction pedal and ensure that it is in neutral.
2. Turn the ignition key to the Run position.
3. When the glow indicator dims, turn the ignition key
to the Start position. Release the key immediately
(Figure
when the engine starts and allow it to return to the
Run position. Allow engine to warm up at mid speed
(without load), then move the throttle control to the
desired position.
Important: Do not run the starter motor more
than 30 seconds at a time or premature starter
failure may result. If the engine fails to start
after 30 seconds, turn the key to the Off position,
recheck the controls and procedures, wait 30
32
Figure 31
3. Lever
g008870