DeWalt DCD200 Instruction Manual page 32

ENglIsh
To Unbind Drain Snake

WARNING: Be sure the cable has come to a complete
stop before setting to reverse position.
1. Set the front handle to the locked position and the
forward/reverse switch to the reverse position.
2. Withdraw the tool a few inches while running slowly in
reverse to free cable.
3. Stop the tool.
4. After the tool has come to a complete stop, switch back
to the forward position.

CAUTION: Running the tool in reverse for extended
periods can cause damage to the cable and accessories.
Only operate in reverse to remove the cable from
an obstruction.
Removing Cable From Drain
1. Set the front handle to the locked position.
2. Set the forward/reverse switch to the forward position.
3. Pull the trigger slightly and pull the tool back to remove
about 6" (15 cm) of cable from the drain.
4. Release the trigger and lock the forward/reverse button
in the center postion.
5. Wipe the exposed cable with a rag, unlock the front
handle and feed it back into the tool.
6. Repeat steps 1–5 until the cable is near the drain
opening. Then feed the remaining cable back into the
drum by hand.

WARNING: Never retract the cable bulb end from
the drain opening while the cable is rotating. The
cable could whip and cause serious injury.
NoTE: Before storing the tool, wash the cable and drum
(refer to Cleaning).
hINT: It's useful to have a stream of water running through
the line to wash fragments away while the machine is in
operation and after. Avoid getting the motor, handle and
battery wet.
Cable Application Chart
Cable Size Pipe Size
1/4" 3/4" to 1-1/2"
(6.35 mm) (19 mm to 38 mm)
5/16" 1-1/4" to 2"
(8 mm) (32 mm to 50 mm)
3/8" 2" to 3"
(9.5 mm) (50 mm to 76 mm)
The 1/4" (6.35 mm) and 5/16" (8 mm) diameter cables with
a bulb end can be rotated through most strainer crossbars
and work well in lines blocked by soft stoppages such as hair,
soap, fats, etc.
Maximum Capacity: 50 ft. (15.2 m) of 1/4" (6.35 mm) and
5/16" (8 mm) cable and 35 ft. (10.7 m) of 3/8" (9.5 mm) cable.
30
Typical Applications
Sinks and bathtub drains
Sinks, wash tubs, small drains
Floor drains, stacks, toilets
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning

WARNING: Remove battery before cleaning tool.

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside
motor and handle of the tool; never immerse any part
of the tool into a liquid.
Rinse, dry and lightly oil the cable after each use to prevent
damage from sediment and drain cleaning chemicals.
Remove the cable and inner drum before rinsing. Refer
to Cable Removal from the Drain Snake and Cable
Drum Installation.
NoTE: The cable can twist, kink or break if overstressed.

WARNING: Wear leather gloves with latex
gloves inside.
Accessories

WARNING: Since accessories, other than those offered
or recommended by D
with this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
D WALT recommended accessories should be used with
e
this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
D WALT accessories available for purchase
e
DCD2000 Inner Drum
DCD2005 25' (7.6 m) 5/16" (8 mm) Bulb Head
Cable
WALT, have not been tested
e